Jump to content
SAU Community

Recommended Posts

Hi Guys,

Just hoping someone can point me in the right direction.

I've got a 96 R33 GTST with K&N Pod, 3" Zorst, BOV and FMIC with boost around 11-12psi (done by a Turbosmart manual bleeder value).

When i go to accelerate (overtaking on the highway) you can hear the pod filter etc going crazy sucking in air but the car doesnt really take off (it used too and it isnt just that i'm used to the car.. i've had it for 2 years and i know somethings wrong). It will take off but struggles and it surges and then hits flat spots and then surges again all the way up the rev range. Seems like something is holding it back.

I do have dud coils but i have taped them with electrical tape and they seem to be ok for a $10 fix (they are really bad without taping).

I have cleaned my AFM once before when i had a very similiar situation and it seemed to have resolved the problem but i dont want to keep getting this problem. I've only driven the car about 2000kms in the last 6mths (also since i cleaned and re-oiled the filter).

Also when travelling on the highway and going to over take (whether in 4th or 5th gear), if i just hammer it, my car cuts out (like the fuel-cut comming in) but if i slowly climb there is no cut out.

If anyone can suggest where i should look at, i'd appreciate. thanks

well the cut out in 5th gear is rich and retard mode. only way to get rid of that is either new ecu or wind the boost down.

how old are your spark plugs? and what type? that could be part of the problem.

Hi,

Thanks for the replies.. Just wondering why when i overtake i 4th or 5th and i slowly put the pedal down it doesnt cut out but when i plant it, the fuel cut comes in... could this be because of a bad bleeder/boost value?

Also, i havent changed my sparkies in a while so maybe i will this weekend and i'll gap them.

Anyways, thanks guys again.

wouldnt think the boost controller would have anything to do with the problem. It will just be fuel cut coming in...R&R as stated before, a/m ecu will fix it. Generally winter will bring upon boost spikes and induce R&R more so if you have the boost set right on that threshold and the occassional squirt mixed with colder climate will bring upon that change.

Yer im in a similar situation dude, with the same b/c as urself.....try winding it back a touch....

Originally posted by r33 racer

Generally winter will bring upon boost spikes and induce R&R more so if you have the boost set right on that threshold and the occassional squirt mixed with colder climate will bring upon that change

Exactly wat i thought! :laugh:

the way that r&r works isn't by boost pressure. it isn't just a case of once it reaches a certain pressure it cuts out. that is why it won't do it if you ease the throttle on.

but yes the cold weather has an effect on it. just wind the boost down a bit.

its based on a ramp scale. i started a thread about this to find out exactly.

what happens is that the ecu has a set maximum airflow per rpm. so if it exceeds that amount it cuts out.

for example, the airflow at 14psi might be within limits at 6000rpm, but not at 3000rpm, so it cuts out. i will draw a graph to illustrate it when i get time.

haha no...i dont think so...try winding the boost down and see how it goes mate. Take things one step at a time...you never do 5 things to fix one problem or you will never know what fixed it.

Thats also an idea below...try some contact cleaner through your afm.

Edited by r33_racer

I didnt notice this problem until last weekend when i went for a long drive and needed to overtake. But the period after re-oiling, i didnt have any problems.

And yes i would love to buy new coil packs but i dont have the money yet.

Well, i'll wind the boost down first and get new sparkies and have em gapped.

Then i'll see how it goes.. I'll clean the AFM anyway.

Thanks guys.. will keep you posted.

Could be a number of things (as usual) but coil packs usually fluctuate when faulty under load which is what you are experiencing when trying to overtake. Which also explains, that when you decrease the amount of boost you are running that the problem will go away.

Theres plenty of advice throughout these forums to detect faulty coil packs.

Hi All,

I've changed my plugs with NGK BCPR6ES (i think that's it) which are standard gapped to 0.8mm and wound down the boost to run 10 or 10.5 (needle on boost gauge is half between 10 and 11). The 33 seems to run quite well.

However saying that, the old plugs didnt look to bad either but who cares when the car is running much better.

thanks alot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...