Jump to content
SAU Community

Autometer C2 Tacho

HOT_R33

By HOT_R33,
in Queensland

 Share

Recommended Posts

HOT_R33 Proficient

HOT_R33

Posted
  • Author
Posted
1.) Check the power to the White (illumination) wire. This is your power input to the light and the amount of power will vary depending on how and where you have it hooked up. The lower the power, the dimmer the light and the higher the power, the brighter the light. A common range is from 6 to 14 volts.

2.) If your tach features LED lighting such as Cobalt, C2, or NV models, and you have confirmed power to the White (illumination) wire, please visit the Ask A Question or Contact Us pages to communicate with our Tech Department.

3.) If your tach uses a replaceable incandescent bulb (check your instructions), inspect the filament of the bulb and replace as necessary. Very few of our tachometers use an incandescent bulb that is not consumer replaceable. If you believe you have one of these units, please visit the Ask A Question or Contact Us pages to inquire about having the bulb replaced.

That Might help...

www.autometer.com

Cheers mike, that helps heeps. So its the white wire, ahh.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • Nizzy_R34
      r34's love to squeal

      By Nizzy_R34 · Posted

      just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • Duncan
      Engine sputter

      By Duncan · Posted

      My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Duncan
      S1 Autech 260RS Wiring Diagrams

      By Duncan · Posted

      Awesome, thanks for sharing!
    • Duncan
      Nissan fuga 450gt android screen

      By Duncan · Posted

      To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...