Jump to content
SAU Community

Overheating

skylinefan

By skylinefan,
in General Maintenance

 Share

Recommended Posts

skylinefan Enthusiast

skylinefan

Posted
Posted

yesterday i changed the upper and lower radiator hoses(very old) the radiator cap and the thermostat.... took it for a drive and thrashed it a little !! but the car still seened to be getting quiet hot ...... and after i unplugged the heat sensor and put it bak in the heat said half in the guage,,,, something is a miss and i just cant figure it out !! sensor? head? and there doesnt seem to be a build up of pressure on the hoses?? me is a little lost .... have i done something wrong ??

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/
Share on other sites
skylinefan Enthusiast

skylinefan

Posted
  • Author
Posted
Obvious question is did u put the thermostat in the right way and did u get the right one?

Are u using an overflow bottle with the rad?

Is the coolant level stayin constant?

If all ok replace the water temp sensor.

hey thanks for the reply, air flow bottle?

coolant seems to be staying level now, and yes the thermostat is thew correct one and its in the same way the other one came out !! im hopeing it isnt the water pump... could that also be it !! and i was planning on doing the water temp sensor on the weekend.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2359920
Share on other sites
MerlinTheHapyPig Mentor

MerlinTheHapyPig

Posted
Posted

how do you know it's overheating?

The "normal" position on the stock temp gauge will sometimes change when you install a thermostat that opens at a different temperature.

Perhaps get an aftermarket water temp gauge to see where you're actually at more accurately

Anyway, if it's definantly overheating and you've ruled out the thermostat, then it's probably the water pump.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2360072
Share on other sites
skylinefan Enthusiast

skylinefan

Posted
  • Author
Posted
how do you know it's overheating?

The "normal" position on the stock temp gauge will sometimes change when you install a thermostat that opens at a different temperature.

Perhaps get an aftermarket water temp gauge to see where you're actually at more accurately

Anyway, if it's definantly overheating and you've ruled out the thermostat, then it's probably the water pump.

ok, but if it was the water pump wouldnt the car idle differntly? ot would the cur run differently? cause the car still kicks well

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2361769
Share on other sites
Rednisr31 Community Regular

Rednisr31

Posted
Posted

it would idle the same

try driving it without the thermostat but of the bearing in the pump is f**ked it fan wont keep running straight, it wont run true to the engine

my mates fan smashed 2 radiators before he fixed his pump, bearing was screwed and the fan moved enough to foul on the radiator (r31 skyline, same shaped pump with more fins inside)

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2361934
Share on other sites
skylinefan Enthusiast

skylinefan

Posted
  • Author
Posted
Obvious question is did u put the thermostat in the right way and did u get the right one?

Are u using an overflow bottle with the rad?

Is the coolant level stayin constant?

If all ok replace the water temp sensor.

ok the coolant isnt staying constant, it builds up in the overflow, and ends up being like 2 inches hight then it was b4 driving it !! im not driveing iit to the stage of it over heating !! just been taking it on test drives ....

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2362015
Share on other sites
skylinefan Enthusiast

skylinefan

Posted
  • Author
Posted

ok further info !! was doing a little more work on the car today !! took it for a drive !! still doesnt seem to be much pressure in the radiator hoses?? car is running fine !1 ideling fine, but AFTER ABOUT 30 MINS OF DRIVEING the heat started to rise !! the overflow keeps filling to the stage where its about to overflow?? im starting to get worried... :teehee: its starting to look like the waterpump i think??

if so how much is a good estimate for the pump and work ?? anyhelp would be benifical

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2365119
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

Pumps have been known to rot out the impeller blades because idiot (previous / Japanese) owners don't use proper coolant.

Pump is around $100. Job takes a (leisurely) couple of hours.

You need to remove the radiator, so while it is out, get it thoroughly cleaned.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2365779
Share on other sites
skylinefan Enthusiast

skylinefan

Posted
  • Author
Posted
Pumps have been known to rot out the impeller blades because idiot (previous / Japanese) owners don't use proper coolant.

Pump is around $100. Job takes a (leisurely) couple of hours.

You need to remove the radiator, so while it is out, get it thoroughly cleaned.

cool thanks for that... i think that job is a little passed my knowledge, so i might have to look into getting it done bysomeone....

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2366737
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...