Jump to content
SAU Community

Recommended Posts

hi guys

BATMBL will be in charge of the GB, so all Q's, PMs & payments will need to go to him.

The 1st GB was a huge success and had to be closed early because of the large amount of people. The 2nd GB is now open and i have put names down of people who expressed their interest for a 2nd GB. Please post in thread if you want to stay in the 2nd GB or want to back out.

The pipes are made here in Australia and are a 304 grade, 2.2mm stainless steel. They will be suitable for both your standard turbo and/or a hi-flowed stock turbo.

The cars & prices for which the pipes are available:

R32 GTST/GTS4 or R33 GTST - $380 DELIVERED

R34 GTT - $410 DELIVERED

Payment method: Direct deposit - (PM BATMBL for bank details, along with your address)

Delivery Method: Registered post

Terms: Once full payment is made, the pipe will be sent within 1-2 working days. If there is no stock left, the pipe will be ordered to be made. This is due to the fact that a high intake of people is expected at once and stock may run out quickly. In the case of this occuring, you may need to wait up to 5 days before the pipe is sent after your payment has cleared. These pipes are hand made, one by one, not on a production line, so it does take some time to make them. This also ensures you get a perfect fitting pipe.

Payment will start to be accepted on 2 August onwards, as this will give me enough time to see if we can get to 10 people or close to it by that date.

If you agree to all the information above and want to be in the GB, please place your interest in the thread along with which pipe you need.

cheers

Edited by Driftn 180
  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

pics of the cats are available on the second post on this thread:

http://www.skylinesaustralia.com/forums/in...howtopic=120070

and pic of the r32/33 pipe is available on the below thread (R34 pipe not shown, but is longer then R32/33):

http://www.skylinesaustralia.com/forums/in...showtopic=74022

anjoO,

which cat were you after for the R34 GTT? I may be able to do the GB price if we can get a round of people because i just finished a cat GB and might just say that i had a few late order and get them at the same price.

as far as i can see in the thread, the following want a cat also:

anjoO

JaiJai

mrgilly

Xizor

jeffworld2

if you can all confirm which type cat you want, i should be able to get you the GB price also if you make the payment same time as the pipe or by end of the week.

cheers

FAT32,

They are all made this way already, so if you didnt need the splitter, its a very easy job for an exhaust place to cut it off for you and shave the area. Some will do it for free, others might charge you $10 or so.

to All,

If you want a CAT as well, PM me with which cat you want along with the pipe and i can do it at the cat GB price. just check the #2 GB for cats and you can make the payment the same time as the pipe. This way i'll send both parts out at the same time in the same packaging.

cheers

ill have the CATCO 3inch CAT (200csi steel inside, bolt-on)

oh and could u give me atotal with the cat plz

thanks

Edited by anjoO
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...