Jump to content
SAU Community

Best Alarm In Sydney?

GTRR

By GTRR,
in Car Audio & Electrical

 Share

Recommended Posts

siddr20 Grand Master

siddr20

Posted
Posted

brant, mongoose have keypads..

Its a tough question to ask which alarm is best. They all do the jobs in one way.

But then a pro will always know how to disarm it.

But i would look at mongoose m80 with kaypad. Heard they good alarms.

Then again someone else might not think so.

Why not try quicktrack?

Installers for brant and mongoose would have to be alan jon. Search sau if you want.

danielr34 Collaborator

danielr34

Posted
Posted
Hi guys, im in the process of installing a alarm system, i was going ahead with the quiktrak but now im thinking otherwise

what else is there on the market that is good? any with trackers? key pads? etc?

thanks!

Autowatch make a very nice keypad which is very reliable

  • 4 weeks later...
Chris_R33GTSt Proficient

Chris_R33GTSt

Posted
Posted

Yep, Autowatch are great. I have a 446lri, which was installed by Leon from www.securityinmotion.com.au. You can tell by the quality of his work that he is a pro. Try stealing my car.. Now the sensetivity is turned up a bit u cant brush past the car without gettin a nice reminter to not touch the painwork ;-)

frx026 Proficient

frx026

Posted
Posted
Yep, Autowatch are great. I have a 446lri, which was installed by Leon from www.securityinmotion.com.au. You can tell by the quality of his work that he is a pro. Try stealing my car..

ok, let me just point something out to you.

NO CAR IS UNSTEALABLE.

Your 1997 R33 Series 2 showing 60,XXX km, with pod filter and cat back 3" exhaust is no exeption. And the northern beaches area is definately not the place to be telling people what alarm you have in the car.

Got my point?

Chris Rogers Grand Master

Chris Rogers

Posted
Posted
yup im 100% sure the m80 alarms can come fitted with kaypad. Ask alan jon. Im pretty sure he said he can install it with keypad.

Cheers

but not a mongoose item. the autowatch one posted earlier will fit anything.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Watermouse
      Original window sticker?

      By Watermouse · Posted

      I got a full sheet set of OEM copied stickers to replace all the faded engine bay ones, great quality too.  Came from England. Someone like that should be able to to make u up what u want so long as u have a quality image to show them 🤷🏻‍♂️
    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
×
×
  • Create New...