Jump to content
SAU Community

Recommended Posts

As the title says, does anyone use this brand of oil, i have heard awesome things about it and im doing a change with the royal purple 10w40 tomorrow....

anyone else using it?

any thoughts on this brand?

Beef

Edited by Beef
Link to comment
https://www.sau.com.au/forums/topic/129567-royal-purple-oils-your-thoughts/
Share on other sites

Beef,

I have been using Royal Purple 10W40 for a while now - ever since my last blow up. After spinning bearings my mechanic did a little research to ensure we were using the best oil available. From his feedback, a lot of the high horsepower guys are using Royal Purple because of its friction coefficient and is an ash free synthetic. Fairly expensive (especially when you have an extended sump), but so far so good.

Theres no such thing as 'ash free'. You can see this from the UOAs. Ash freemeans there are no metallic type additives in the formulation which is clearly not true.

IMO Royal Purple's street oils are OK (no evidence to suggest they are better than Mobil1 in real world testing), but their racing oils such as RP21 are quite good.

Beef,

I have been using Royal Purple 10W40 for a while now - ever since my last blow up. After spinning bearings my mechanic did a little research to ensure we were using the best oil available. From his feedback, a lot of the high horsepower guys are using Royal Purple because of its friction coefficient and is an ash free synthetic. Fairly expensive (especially when you have an extended sump), but so far so good.

The flash point for RP 10w40 are only 204'c (HTHS 4.02), the RP 15w40 flash point do look better with 224'c but (HTHS 3.6) only. IMO both not really ideal for hot running turbo engine.

The RP 10w30 do look better with flash point at 235'c and HTHS of 3.3, i would say go for the 10w30 for faster turbo spool and better thermal stability.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...