Jump to content
SAU Community

Gb: Brand New Z32 Afm's - $330.00 Each


Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

Blitz, this may seem like a sil question, but is there any difference between the genuine Bosch item and a Nismo one?

The Bosch/Nissan Z32 AFM's are 80mm,where the Nismo/Tomei units are smaller in physical size, but still have increased voltage capabilities over the standard AFM - They are also significantly more expensive and tuners I have spoken to seem to prefer the standard type 80mm Z32 over the Nismo/Tomei type units.

Hope this helps

Payment made and email sent to Darron

Alan

Hi Alan, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581246)

Cheers,

Nick

Received the AFM yesterday, damn quick delivery :ninja: Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Your very welcome mate :ninja:

Payment made and email sent to Darron :ninja:

Gday Matt, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581247)

Cheers,

Nick

CAn you hook these units up to a stock RB20DET and see a difference or will it be just a waste of time until i get my Power FC?

Thanks guys

You will need to wait until you have a Power FC :D

Woohoo! Received mine today! thanks mate! :D

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Received the AFM yesterday, damn quick delivery :D Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Hey AcoustiK, try this thread, might help you a bit! :yes:

http://www.skylinesaustralia.com/forums/in...howtopic=116520

Woohoo! Received mine today! thanks mate! ;)

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Hi Dave, glad to hear it arrived safely - The dent in the mesh wont be a problem, in some cases people remove the mesh all together.

Hey Blitz,

Just transfered the funds, and emailed Darron too.

Thanks

Hi Nikki, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581250)

Cheers,

Nick

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...