Jump to content
SAU Community

Gb: Brand New Z32 Afm's - $330.00 Each


Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

Blitz, this may seem like a sil question, but is there any difference between the genuine Bosch item and a Nismo one?

The Bosch/Nissan Z32 AFM's are 80mm,where the Nismo/Tomei units are smaller in physical size, but still have increased voltage capabilities over the standard AFM - They are also significantly more expensive and tuners I have spoken to seem to prefer the standard type 80mm Z32 over the Nismo/Tomei type units.

Hope this helps

Payment made and email sent to Darron

Alan

Hi Alan, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581246)

Cheers,

Nick

Received the AFM yesterday, damn quick delivery :ninja: Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Your very welcome mate :ninja:

Payment made and email sent to Darron :ninja:

Gday Matt, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581247)

Cheers,

Nick

CAn you hook these units up to a stock RB20DET and see a difference or will it be just a waste of time until i get my Power FC?

Thanks guys

You will need to wait until you have a Power FC :D

Woohoo! Received mine today! thanks mate! :D

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Received the AFM yesterday, damn quick delivery :D Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Hey AcoustiK, try this thread, might help you a bit! :yes:

http://www.skylinesaustralia.com/forums/in...howtopic=116520

Woohoo! Received mine today! thanks mate! ;)

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Hi Dave, glad to hear it arrived safely - The dent in the mesh wont be a problem, in some cases people remove the mesh all together.

Hey Blitz,

Just transfered the funds, and emailed Darron too.

Thanks

Hi Nikki, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581250)

Cheers,

Nick

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...