Jump to content
SAU Community

Recommended Posts

howdy,

i have a mr30 that i just put a fj20et in it, i bought a dr30 halfcut, but i have run into a problem my original tailshaft is too long :O does any1 know of a replacement tailshaft out of any other datsun or local car that will fit straight in, or does any know the length of the dr30 4 door tailshaft . thanks for any help.

cheers shaun.

Link to comment
https://www.sau.com.au/forums/topic/131341-tailshaft/
Share on other sites

howdy,

i have a mr30 that i just put a fj20et in it, i bought a dr30 halfcut, but i have run into a problem my original tailshaft is too long :P does any1 know of a replacement tailshaft out of any other datsun or local car that will fit straight in, or does any know the length of the dr30 4 door tailshaft . thanks for any help.

cheers shaun.

Shaun,

I have a DR 4 door tailshaft in the garage, can you tell me the length of your MR tailshaft so I have something to compare.

Cheers, D

Link to comment
https://www.sau.com.au/forums/topic/131341-tailshaft/#findComment-2430100
Share on other sites

Shaun,

I have a DR 4 door tailshaft in the garage, can you tell me the length of your MR tailshaft so I have something to compare.

Cheers, D

cheers mate i will measure it tommorrow and let you know what i come up with. thanks heaps.

Shaun.

Link to comment
https://www.sau.com.au/forums/topic/131341-tailshaft/#findComment-2432794
Share on other sites

i dunno, nissan seem to keep things quite common..... i had an L series( 280zx) gear box in my skyline line and when i went to the rb gear ( r32 gtst) box, the yoke was exactly the same...... lenghts may be different but you should be able to find some thin in a wreckin yard.

i had the problem i kept snapping the rear yokes on my tail shaft in my 66 skyline gt.... went down the wreckin yard armed with a tail shaft lenght and pitch for the bolt pattern and spline config for the gear box and end up comming out with a datsun stanza 1600 auto tail shaft that fitted perfectly.......

best bet is to go down to ya local yard that has lots of datsun/ nissans and ask if ya can have a crawl thru to sus out wots wot!!

Edited by 66 skyline gt
Link to comment
https://www.sau.com.au/forums/topic/131341-tailshaft/#findComment-2441309
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...