Jump to content
SAU Community

Recommended Posts

hi all.

i bought these a while ago with the intention of putting them in my mistress but have decided to sell and wait till i can afford a full adj' coilover setup!

i bought them off ebay a few months ago for just over 270.

i feel that $200 is a fair price. 200 INCLUDING shipping that is. pick up in the mornington peninsula area would be alright too (say $180 for pick up).

PRICE DROP!!!- NOW ASKING $170 INCLUDING POSTAGE

according to the ebayer i bought them off they lower the car 30-35mm.

dont know for sure but ive been told from a reasonable source that they are much stiffer than the stock springs too (but dont hold me to that!)

to contact me you can do the obvious: pm or reply in this post. or call/ sms my mobile on 0423 043 495. james is my name.

not particularly negotiable on price- unless you can show me a genuine place that sells the same item new for much cheaper.

cheers. james.

sub wooofers go bump bump bump bump.

just like me in this reply.

bump

EDIT: if there is anything in the list in my signature that you are trying to sell that you are willing to swap for, we can make some sort of arrangement. cheers!

  • 2 weeks later...

alrighty then.

i called up king springs and they themselves had said that the rear ones are good for a both the GTS-T and GTS-4 (they said "its suitable for both the rear wheel dirve and the 4WD" so i assume that its ok for the GTR) HOWEVER the FRONT springs are only good for the gts/ gts-t.

PATTO: steven from king springs said that it lowers it 25- 30 mm. which isnt much but ive driven a 32 with these springs on them and it look good, and is easy to drive aswell.

cheers. james.

If you want to ask any more questions please call them on (07) 5539 6700 and quote the part numbers KDRL 102 (the rear ones) and KDFL 101 (fronts)

this was the effect of King Spring Sport lows after only a day or so, still got a bit of dropping to do:

http://www.nissansilvia.com/forums/index.p...t&p=2333355

fair bit lower, but most importantly alot better handling.

Edited by nisskid

bump!

desperate to get rid of them, not desperate to lower the price though.

hurry up and buy these someone!

cheers. james.

please read above.

lowers the car 25-30mm.

take a ruler to your car and find out what the height is take off 25-30mm.

BAM! thats how low it sits.

cheers.

im located in VIC so if anyone want to pic up from here...

however a mate is selling these in sydney.

heres the link.

http://www.skylinesaustralia.com/forums/in...howtopic=134177

cheers. james.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...