Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
what turbo or turbo's are you running to make 400atw @ 1bar? please dont tell me they are stock!

well thats the thing, i dont know. I bought it like that. They look standard from the outside but i am no expert. Maybe they are high flowed but can not say for sure.

  • 2 weeks later...
well thats the thing, i dont know. I bought it like that. They look standard from the outside but i am no expert. Maybe they are high flowed but can not say for sure.

Maybe N1's????

I cant see stocks doing that power on that boost

edit; forgot to ask is this a 1990 model????

Edited by gtr660hp
  • 4 weeks later...
Maybe N1's????

I cant see stocks doing that power on that boost

edit; forgot to ask is this a 1990 model????

wrong i have seen 380 on stock turbos 16psi.. if u dont believe me check www.clubhighrollers.com and check club rides for damos 32 GTR

good luck with the sale

Free BUMP!!!

  • 2 weeks later...

PRICE DROP!!!!

This car has to go

alarm cost me over a $1000

power fc and tune cost over $2000

R33 engine and install cost me shit loads, im not going to get anywhere near my money back, car just has to go. very sad

recently had new starter motor in as well as new battery. Also have receipts for lots of other little shit

car must go

Edited by RRR32_GoDzIlLa
whats all over the back seats and passenger chair? and back floor?

lol, its just been brushed the wrong way, there not marks. ya kno what i mean?

and it's at night so theres some shadows, maybe i should take a better photo cuz it does look like theres marks everywhere

Edited by RRR32_GoDzIlLa
  • 4 weeks later...
  • 3 weeks later...
  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...