Jump to content
SAU Community

Recommended Posts

Calder is on this friday guys, the 4th of April, there will be a group of us heading out so any1 wanting to go and wathc or run their car feel free to join us.

Details are:

Meet at Calder at 5:30, scruitineer if you are running, grab a good spot, and have some fun.

$55 to race (unlimited runs), $17 to spectate

So far we have:-

JET-33

32_ENVY

Predator666

HOTSKY

DZNUTZ

DJ_L3ThAL

Al

Baileylsd

Horus

NizmoR34

List ya name here so we can get an idea of whos comin, and so we can organise a way to meet up (mob numbers etc)

Should be a good nite so i hope to see as many faces there as possible.

JET-33

Link to comment
https://www.sau.com.au/forums/topic/13347-calder-342003/
Share on other sites

My car will be entered!!!

Alan: 0427076490 (Mob)

Have to remember to grab my brothers helmet.

Have to get home, put my stockies back on, then drive down to calder. Hope i finish early!

I was considering putting some semi slicks on, but decided against it as i want to see the gains (If any, but better be otherwise i am going to kick some more BUTT on Saturday morning) of my modifications since my last runs.

The rims will be wearing 205 yokahamas (sp). Unfortunately they are a hard compound, and mated with my stiff Tein suspension, the car has a far from optimal set-up. :D

I am just laying down a bunch of excuses to cover my ass when someone else kicks my butt down the 1/4 :D . Just remember to be gentle as this is only my second time, i don't believe in street drags (my license is my job and vis-versa), and i owned a 350,000+km XF falcon on GAS before this!!! :uh-huh:

:burnout: All in all i am going to give it a go and have a fun evening with you lot! :burnout:

DJ_L3ThAL

DON'T BE A PUUUSSSSSY and have a run. Once you see all the other 'lines going down the 1/4 you will regret not entering.

Link to comment
https://www.sau.com.au/forums/topic/13347-calder-342003/#findComment-256545
Share on other sites

ahaha.. bad luck ambz.. you miss out .. i'll take some photos for ya but its never quite the same as being there :( i told nark that it was a bad idea to leave it here 'cause everybody would miss it, but he didn't listen.

I'm skipping out at 4:30pm to get there ..

my car is ready to booocha .. my bar is patched up, my helmet is ready, my car is tuned hard... and :burnout:

I'm just gonna run my standard street tyres (235/45R17) cbf sticking my stockies back on (no grips anyway)

Link to comment
https://www.sau.com.au/forums/topic/13347-calder-342003/#findComment-257786
Share on other sites

I thought u guys had been talking about going for like a week already...[im sure there was another post in vic section few days back]

AMBZ: you dont have to get there @ 6 if your not running, you can still go like between 7-8 and see heaps o action...I prolly wont be there at 5:30 / 6 - too much traffic onthe way at that time! If I am going it may be around 7...

Link to comment
https://www.sau.com.au/forums/topic/13347-calder-342003/#findComment-257826
Share on other sites

prediator since we both have the same power we should line each other up and run man!! i am in, prediator if u dont come u r a p*u*s*s*yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy!!

And i'd just like to remind denham who is all of a sudden very quiet about this now.. whos the ****ing ***** now??? !! :(

Link to comment
https://www.sau.com.au/forums/topic/13347-calder-342003/#findComment-257898
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...