Jump to content
SAU Community

Recommended Posts

Slightly freaked out here. Have installed all the CDs libraries from the howto. Punched in my VIN Code and "model series can not be found for this vin no input model or model series" is the result. Tried someone elses ecr33 and got a result. Mine doesn't work. Typed in the model number:

ggkbrtfr33vdac---- and I got part of a result. It then accepted the vin number and gave me some details engine/mt etc. Did this happen to anyone else? Is this bad?

ecr33025105

Edited by axelmasok
Gives me the same error for that vin number, you sure you have it correct?

100% double and triple checked. The model number I have seems to be valid. The VIN as you see is not. I read somewhere about how the plate is attached to the firewall and to pick ones that have been tampered with....mine has two small plastic "rivets" that attach it to the firewall, the plate is thin and can get my fingernail behind it. Is this blue blate original?

Hi can anyone check out if anything interesting comes up with RA31GASMP-EC it's off my cefiro... Mainly because I'm trying to source brakes parts and the parts I got are WAY off, so need to know if it's a Touring/Comfort/Sport edition etc.

Many Thanks,

Grant.

Edited by QUIKBLADE
  • 2 weeks later...
  • 2 weeks later...
Can someone check this

VIN 6u9000ecr33107218

THANKS HEAPS! i cant seem to post new topics so id thought id do it here.

Hi Guys,

It would be appreciated if somebody could please check the following VIN on FAST for me.

6T91MPAAAN1BAD007

Thanks in advance.

Marc2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...