Jump to content
SAU Community

Recommended Posts

I was thinking about posting the exact same question.

My fuel economy is up shit creek. I'm getting 15L/100 OFF BOOST and then 20+L/100 when giving it a bit of stick.

I've recently had a new fuel pump and new timing belt.

What stuff should I check?

Whats there to check with the 02 Sensor?

Link to comment
https://www.sau.com.au/forums/topic/13399-fuel-economy/#findComment-259054
Share on other sites

I was getting really bad Fuel Economy a few months ago (lucky to get 200k to a tank) I replaced my o2 sensor 4 a ford unit all is now good.

Long steady drives i get over 500 k to a tank, arround town strapping it i get at worst 400k's.

I would get you O2 sensor replaced.

The ford unit is the same as the nissan one only cheaper and you need to change the plug to the nissan one 4 it to fit. For under $90 well worth it.

Regards

Damqik

Link to comment
https://www.sau.com.au/forums/topic/13399-fuel-economy/#findComment-259291
Share on other sites

The o2 sensor is located on the back of the turbo & has 3 wires going to it. I got my replacement one from Barnes high performance Nambor (he can fit 4 u tho I did mine myself)

The Afm is mounted on the back of the air box has about 5 wires going to it, give it a spray with Co Contact cleaner made by CRC

try the following link for more info

http://www.wave.co.nz/~hksnz/techfiles/oxy...orlifespan.html

Link to comment
https://www.sau.com.au/forums/topic/13399-fuel-economy/#findComment-259294
Share on other sites

The O2 sensor is only used by the ECU during closed loop operation. Even with a faulty O2 sensor your fuel economy should only drop a bit.

300km to a tank is a significant drop. I doubt it'll be your O2 sensor. Could be a bad tune, fault spark plugs, a blocked/damaged cat.

Link to comment
https://www.sau.com.au/forums/topic/13399-fuel-economy/#findComment-259302
Share on other sites

Yeah, I'm talking 300km at BEST.

If I give it a bit I'm lucky to get 250.

I spoke to a mechanic about it today.

He's gonna replace it for me under the warranty I got with my car.

Who says those warranties aren't worth shit hey?

We'll see how it goes hey?

Link to comment
https://www.sau.com.au/forums/topic/13399-fuel-economy/#findComment-259877
Share on other sites

  • 3 weeks later...
Originally posted by poyz

The O2 sensor is only used by the ECU during closed loop operation. Even with a faulty O2 sensor your fuel economy should only drop a bit.

300km to a tank is a significant drop. I doubt it'll be your O2 sensor. Could be a bad tune, fault spark plugs, a blocked/damaged cat.

I disagree. I changed my O2 sensor, and that has made all the difference. I'm getting waaaaaaay better economy then what i did before.

Link to comment
https://www.sau.com.au/forums/topic/13399-fuel-economy/#findComment-292896
Share on other sites

Originally posted by poyz

The O2 sensor is only used by the ECU during closed loop operation. Even with a faulty O2 sensor your fuel economy should only drop a bit.

300km to a tank is a significant drop. I doubt it'll be your O2 sensor. Could be a bad tune, fault spark plugs, a blocked/damaged cat.

Actually skylines spend most of their time in closed loop the only time there not is @ full throttle or accelerating off.

If the O2 sensor is stuffed the ecu gos into the safe (Rich) limp home mode.

Therefore as many people have said replacing the O2 sensor has given them much better fuel economy if you have a stock or near stock car and get shit economy I'd recommend replacing it.

Link to comment
https://www.sau.com.au/forums/topic/13399-fuel-economy/#findComment-293313
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...