Jump to content
SAU Community

Recommended Posts

yep, i just followed these instructions here

http://www.skylinesaustralia.com/forums/in...=57&t=58778

its not hard, i reakon i did it in an hour. R33s have electronic hicas so theres no messing about with power steering lines. its just a case of unbolt the hicas motor and bolt in the locker bar & yep u will need a rear wheel allignment afterwards. ;)

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

no worries for the lend of the power tools guys - I wish I didn't already have plans, I would have stayed to help you. Missed Darren too - what a bummer .... I must have left too early. Ah well next time!

Yeh i think i just missed you too, should have got off ma ass earlier and come around! The whole Barbie and work on car thing sounds like a good idea, will have to pick a nice day and not toooooooo freakin hot either, otherwise it will turn into a drink beer and sit on our ass day......... which i'm not saying is a baaaad idea :(:D

lol .... I am sure that is what the day would turn into anyhow .... maybe pick a 35 degree day, we can start at 9am, mod until 12pm, jump into the spa/drink beer/eat barbie/play darts & pool until 4pm when it cools down a little, then back into some more modding until 7pm, then repeat step 2 :D

My latest pet project (apart from my 'leatherette' seats) is to put some 10mm chipboard on the drivers side 'wall' of the boot (behind the lining) in order to mount a fire extinguisher, some spare fuel, spare water and tools. Not a big job, but would require removing the boot skins, measuring up, cutting the chipboard to shape, securing/deadening the chipboard and restoring the boot lining. It is the sort of job we could do to 6-10 Skylines at once if anyone else was interested.

lol .... I am sure that is what the day would turn into anyhow .... maybe pick a 35 degree day, we can start at 9am, mod until 12pm, jump into the spa/drink beer/eat barbie/play darts & pool until 4pm when it cools down a little, then back into some more modding until 7pm, then repeat step 2 :D

great in theory but as well all know in practice unexpected sh!t happens and it takes way longer then expected. you know that bolt we tried to get off andrew? well we ended up screwing it up again - thank gosh we later had access to vice grips.

DOH! ... I was going to ask you how it went.

And yes, as we have discovered many times it always takes much longer to do than you think - but once we got a template done it would be dead easy to do more.

So, is anyone up for this project, or have another one in mind? I might just organise a day in a few weeks time - I'm thinking maybe 14th October? (Week after dyno day). I would prefer to do it before I head to Singapore .... but could wait until I got back.

My latest pet project (apart from my 'leatherette' seats) is to put some 10mm chipboard on the drivers side 'wall' of the boot (behind the lining) in order to mount a fire extinguisher, some spare fuel, spare water and tools. Not a big job, but would require removing the boot skins, measuring up, cutting the chipboard to shape, securing/deadening the chipboard and restoring the boot lining. It is the sort of job we could do to 6-10 Skylines at once if anyone else was interested.

sounds good i have a fire extinguisher floating in my boot and i want to mod the back where thre rear cover covers the boot battery and put sum MDF with twin 10" subs this is long way off though

**edit**

i found this after looking for boot pictures

http://autospeed.drive.com.au/cms/A_1212/article.html

Edited by Madaz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...