Jump to content
SAU Community

Alternative Bov?

Lachlan33

By Lachlan33,
in Engines & Forced Induction

 Share

Recommended Posts

Lachlan33 Community Regular

Lachlan33

Posted
Posted

Hi guys.

I have a couple issues with my 33, mainly if im creeping forward in traffic and jab it for a sec, when returning to idle it drops very low and nearly stalls, has actually stalled a couple times.

Now when I got the car a month or so ago it had an Atmo BOV on it and I believe that is whats causing the issue here, inthat its dumping air that its already factored in to be fueled so it overfuels for a second, runs rich and nearly dies.

I must say, I do like the psssh sound but.

Anyway, im wondering if there are alternatives out there, or is it possible to adjust the BOV to not vent so easily, so its only blowing off under decent levels of presure? Or am Is my best bet to buy an aftermarket plumb back BOV and go without the Pssh.

Or as another option is there a way to trick the ECU to stop this occuring?

Advice is apreciated.

Link to comment
https://www.sau.com.au/forums/topic/134476-alternative-bov/
Share on other sites
AzzurrA Grand Master

AzzurrA

Posted
Posted

my plumb-back is just as loud, if not louder, than alot of Atmo BOV's i've heard... (assuming you have a Pod Filter as well)

it's a GReddy Type S.

the stock BOV is also quite loud, and works just as good... can pick them up for around $30 or less, so just pick one up, sell the atmo bov, and you'll have a car that's running better, will still sound tough, and you'll make money from selling the atmo one :(

Link to comment
https://www.sau.com.au/forums/topic/134476-alternative-bov/#findComment-2500967
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

Lachlan33- try tightening the spring tension, and possibly get some new plugs. i had a few mates with the same issue. new plugs solved it.

[mez]- i had the problem where it would die after giving it a bit on the stock bov. new plugs fixed that.

Link to comment
https://www.sau.com.au/forums/topic/134476-alternative-bov/#findComment-2501854
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • thomasLait
      New Stegea Owner

      By thomasLait · Posted

      Hey everyone, I recently bought myself a 2001 Nissan Stegea M35, and I've had a few issues that I had to fix, my car would start intermittently and I had a bad rocker cover leak, after a couple days of looking I finally found a part number that interchanges with the OEM starter as the OEM starters at $1300 and I can't afford that, this starter was only $270 and I replaced the start and still had the same issues, I posted a video asking for help online and it went very well, some guy said it was probably a bad ignition switch so I took my dash apart and turns out my ignition switch was half screwed in and was loose, once it was tightened it fired right up, I found a local place called "Boost factory" and they sold me a part of OEM Nissan rocker covers, they were $600 which was a shocker but I couldn't find them anywhere else, so I installed them and fixed my oil leak as the old rocker cover was cracked and warped, I now need to replace my boost air inlet hoses as they have some cracks.
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      I am being real ocd and do not want to make amy mistakes so appreciate all help provided. I am overly cautious so asking for opinion even if i know the answer   few questions,   1.re tensioner, should spring be greased lightly?    2.tensioner has two washers , one pressure washer and other has recessed/ seat. I am going to put the recessed one facing tensioner where edges are cut out and pressure washer on top   3. my car has custom triger kit sold few years ago by guy who initially built the engine. I moved the crank gear and it moved in and out easy, only way to remove belt is to slide the crankshaft gear forward which I did. I have seen these being very tough to move , anything to do with my woodruff key?   it has a crank sensor shown in purple which I assume reads from the 12 teeth position mounted to the crankcase gear   4. timing belt doesn’t have arrow stating front or back just a arrow which I think is direction of rotation . Do you agree?   5.i figured out why my crankcase cover was worn as there was no washer installed over the crankcase cover before the harmonic balancer was put in place. It is missing, anyone knows the part number? It looks like this https://justjap.com/products/genuine-nissan-crankshaft-timing-gear-rear-plate-washer-nissan-s13-ca18-a31-r32-rb20-r33-r34-c33-c34-c35-rb25?currency=USD   https://tinypic.host/image/IMG-4535.382Zy2 https://tinypic.host/image/IMG-4537.382dSz https://tinypic.host/image/IMG-4534.382q4U  
    • TurboTapin
      New fix for low tyre pressure from bmw

      By TurboTapin · Posted

      CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Dose Pipe Sutututu
      Another little story of weird shit happening

      By Dose Pipe Sutututu · Posted

      Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
×
×
  • Create New...