Jump to content
SAU Community

Recommended Posts

Theres lots of posts about spark plugs on here but ive got a question.. :D

R33 gtst usual mods standard turbo..

Re-moved "iridium nismo 8" spark plugs from car (god knows what these are? 0.8 gap?)

Put in NGK Iridium BKR5EIX-11, gapped to 0.8 (i know you're not supposed to gap iridiums).

I wanted to put in BKR6EIX, but id allready bought the BKR5EIX.

Running with the BKR5EIX 's the engine wasnt even coming onto boost it was just pinging and spluttering everywhere.. with low down torque not really there either..

I put the Old iridium nismo 8 plugs back in and all is now good and back to normal..

So im guessing the Iridium BKR5EIX (5 heat rating) is too hotter a plug?

I know i should have the 6 heat range, BKR6EIX, for the kind of mods i have, but would the 5 really do this kind of thing to the performance of my 33?

Any feedback would be great.

Looks like ive just wasted $100 on the damn wrong heat range sprakies.. :( , Dumbass.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/
Share on other sites

Theres lots of posts about spark plugs on here but ive got a question.. :nuke:

R33 gtst usual mods standard turbo..

Re-moved "iridium nismo 8" spark plugs from car (god knows what these are? 0.8 gap?)

Put in NGK Iridium BKR5EIX-11, gapped to 0.8 (i know you're not supposed to gap iridiums).

I wanted to put in BKR6EIX, but id allready bought the BKR5EIX.

Running with the BKR5EIX 's the engine wasnt even coming onto boost it was just pinging and spluttering everywhere.. with low down torque not really there either..

I put the Old iridium nismo 8 plugs back in and all is now good and back to normal..

So im guessing the Iridium BKR5EIX (5 heat rating) is too hotter a plug?

I know i should have the 6 heat range, BKR6EIX, for the kind of mods i have, but would the 5 really do this kind of thing to the performance of my 33?

Any feedback would be great.

Looks like ive just wasted $100 on the damn wrong heat range sprakies.. :) , Dumbass.

Yah think you have got yourself some hot plugs, put it ip in ebay and sell at half the cost. At least you can recover something back.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2517133
Share on other sites

you can't go past the plugs with the code BCPR6ES. they are only copper and are about $3 each (better than about $20 each for iridiums). i've had mine in for about 10,000kms at between 12 and 14psi and they haven't missed a beat. it had iridiums in there and they were dead after 20,000ks. i'm going to change them again at the next oil change (at $24 a set, why not)

but a guy i know put platinum plugs in (heat range 5) and it pings like a bitch, and pops and farts. he took me for a spin in it last night, but he wouldn't listen when i told him his plugs where wrong (1 of those know-it-all types).

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2522759
Share on other sites

you can't go past the plugs with the code BCPR6ES. they are only copper and are about $3 each (better than about $20 each for iridiums). i've had mine in for about 10,000kms at between 12 and 14psi and they haven't missed a beat. it had iridiums in there and they were dead after 20,000ks. i'm going to change them again at the next oil change (at $24 a set, why not)

but a guy i know put platinum plugs in (heat range 5) and it pings like a bitch, and pops and farts. he took me for a spin in it last night, but he wouldn't listen when i told him his plugs where wrong (1 of those know-it-all types).

Sometime cheap is not necessary bad and expensive is not necessary good. The key is to choose the correct form, fit and function that cater to your engine. The BCP6ES are without the V groove, choose the BKR6E-11 (gap down when necessary) which cost around there too.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2522802
Share on other sites

It all depends on the mods you have.

a mildly modded car shouldn't have major issues running a 5 as they are the stock replacement plug.

A 6 heat range plug is a good move with more boost up to about 1.1bar/16psi. bcpr6es/bkr6es is .8 copper out of the box, bcpr6e or bk.. is the v groove option.

A 7 over that up to low 20psi

I'd start with a 6 bcpr6es as they are cheap enough. If no good then make a few enquiries about the nismo plugs and try a copper 7.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2522889
Share on other sites

cheers fellas..

Yeh ill try the bcpr6es hopefully the 6 heat range is better. didnt realise a 5 heat range would be so S!@T

I might even keep the old nismo 8 iridiums in there and just clean them gently..

Ive got the old typical coilpack hairline cracks too, might fix them up as ill probably need too one day anyway..

thanks for the confirmation about the plugs.

Lata.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2539658
Share on other sites

hey i am more or less going through the same thing i have been using 7es in my 33 and have had no real problems went to enquire about iridiums and could get them for about $18.oo each and the same for platiniums but could not get them in 7,s ended back with old faithful bcp7es for grand total of $21.00 ,cheers

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2540931
Share on other sites

  • 2 weeks later...
Don't know if this has been said but you can't compare all plugs by their number e.g. 5 or 6 as some plug manufacturers hotter and colder plugs ranges move in opposite directions.

yeh cheers, i know, i was just talking about ngk's.

ill be going the $21 option too.. ;)

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2570605
Share on other sites

mine was missing on boost...heat shrinked my coils and gapped my plugs at 0.8 that fixed it...then turned the boost up to around 12psi and it started missing again so i went for the bcpr7es gapped at 0.8 and everytihing is now sweet! id definatly recomend going for the 7...+ it costs like 24 bux!

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2570952
Share on other sites

i'm using the bcpr6es and i'm running 14psi with stock coils. they pop and fart on the very odd occasion, but they are about 7000km old. i'm going to go to the 7 heat range on the new plugs, just to get the heat down.

Remember to check your colder plug for fouling...

NGK FAQ

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2571819
Share on other sites

You can't go wrong with the BCPR6ES plugs. I had a set of splitfire plugs in mine which cost around the $20 a plug mark. They lasted all of 3 weeks before they started missing. Then the car sat for 2 weeks in the spray shop and i went to pick it up and it wouldn't start!

A trip down to Autobarn and 6 x BCPR6ES later and they haven't missed a beat. This was in October last year as well so they're probably due for a change! :P

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2574762
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
×
×
  • Create New...