Jump to content
SAU Community

Recommended Posts

Hey guys,

Im looking at starting mods to my 33GTST and im contemplating Turbo back exhaust, FMIC and boost controller.

Was looking at Justjap's range, a Trust Intercooler kit is $1,299, where as a JJR Type 2 Intercooler kit is a mere $550.

What are the main differences here? I dont really need anything super duper but I don't want to buy crap either.

And I was also looking at the X-force stainless steel turbo back system. Anyone fitted that before?

Sorry if this has been asked a billion times before (which im sure it has)

Edited by Lachlan33
Link to comment
https://www.sau.com.au/forums/topic/136083-jjr-intercoolers-from-justjap/
Share on other sites

I have just had one of the JJR Type 2 intercooler kits fitted to my R32 GTS-T and the quality and fit of the kit is outstanding.

The piping and clamps are of very high quality and they dont use the tiny weak clamps that some other kits on the market do.

The cores themselves have been proven in applications exceeding 300rwkw so for the majority of vehicles they are an excellent choice.

I will post a pic later tonight if I have a moment.

Value for money? unbeatable - Plus the owner Steve is on SAU under the username 'Just Jap' and they offer most of their products to SAU members at a discount.

Would the front bar of a S1 R33 need altering to fit a 600x300x76 intercooler? $550 for a type 2 kit seems very reasonable, especially if the IC actually does a decent job.

How much am I looking at for fitting? If I can get away without hacking up the front of the car then id be happy.

Would the front bar of a S1 R33 need altering to fit a 600x300x76 intercooler? $550 for a type 2 kit seems very reasonable, especially if the IC actually does a decent job.

How much am I looking at for fitting? If I can get away without hacking up the front of the car then id be happy.

Any 600 x 300 x 76mm intercooler on an R33 GTS-T will require some trimming to the front bar

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...