Jump to content
SAU Community

Recommended Posts

They're big, cheap, and American.

Having said that I have been tempted to try them - they make 11ty-billion different types of calipers!

As long as the design is OK(ie are stiff enough across the bridge, take a large diameter rotor / thick rotor etc), they should work fine...

Give it a shot and let us know how you go!

If you need some radial mounts machined I might be able to put you on to someone

cheers

Link to comment
https://www.sau.com.au/forums/topic/136224-wilwood/#findComment-2533227
Share on other sites

haha I can be the guinea pig!! :O

I'm very tempted at the moment... Basically I've found a full kit that uses the superlite 4 piston caliper, a two piece 330mm rotor, braided lines, pads, bias valve, brackets etc for not much money... basically a little bit more than it would cost me to buy caliper extension brackets, rebuild my existing 32 4 pots, and getting some DBA 5000's, so yes, very tempting...

Link to comment
https://www.sau.com.au/forums/topic/136224-wilwood/#findComment-2533523
Share on other sites

As Ronin said, Wilowood make a caliper for every man and his dog. So jsut check the model of caliper and make sure the pistons arent smaller then what you are running at the moment.

Im with you, i often look at the Wilwood gear and what they can be bought for. They have calipers that go for $5000 each, but they also have good 4 pot and 6 pot calipers that are between $600-800 each so is tempting :laugh:

Link to comment
https://www.sau.com.au/forums/topic/136224-wilwood/#findComment-2533907
Share on other sites

wilwood have a good selection of pads available,

its just a matter of getting the right one.

we started using a harsh compound and new rda slotted rotors

would only just last a rally. now use a softer compound

and get 2 rallies out of rotors with similar stopping power

and not so touchy

Link to comment
https://www.sau.com.au/forums/topic/136224-wilwood/#findComment-2535418
Share on other sites

Thanks for the feedback guys.

Dougmo, which compound do you use, and are they readily available here??

The caliper that comes with the kit is the Superlite 4, so I'll have a look into the piston size. I wouldn't mind going the Superlite 6, but it's probably a bit overkill, and I'm going to have trouble getting them inside a 17 inch rim...

Link to comment
https://www.sau.com.au/forums/topic/136224-wilwood/#findComment-2535530
Share on other sites

Yeah, seen those mate, that's where I got my pad choice from :huh:

Thanks though.

no probs.

btw, you shouldn't have a problem fitting the 6-piston calipers in a 17" wheel as Wilwood have a brake kit for the sierra cossie with 6-piston calipers, 323mm rotors and they fit inside 17's.

Link to comment
https://www.sau.com.au/forums/topic/136224-wilwood/#findComment-2546041
Share on other sites

Really?? Cool, I'll have a look into it, and see what they say.

Cheers man.

Btw, this is the kit I'm looking at, optioned with Polymatrix E's and Slotted, Zinc coated rotors

http://wilwood.com/BrakeKits/Pages/04/index.asp

Link to comment
https://www.sau.com.au/forums/topic/136224-wilwood/#findComment-2548401
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...