Jump to content
SAU Community

Recommended Posts

So if those cars with high inlet temps were to pull up next to another car with low inlet temps but same power on the dyno down at the local drag stip which will accelerate and run down the 1/4 quicker? My bet is the one with the low IT temps. But the power figures are the same. wtf. :(

Or think of it this way... Same car same car identical power curves at the same km/h, ones a turbo 6 ones a v8. The turbo 6 has had some pretty funky correction on its power curve due to its higher inlet temps. Which one will run down the 1/4 quicker? The N/A with its lower IT temps.

  • Replies 113
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yep, common sense would say the 3rd one has the wrong IT :(

I'm thinking it was something else done wrong that gave such a massive power figure on mine (for a stock 33), so hopefully results similar to the norm can be acheived with the more accurate IT temp, so long as everything else is done correctly

tiz all too confusing to me

I'll just be happy to see a result that is 'normal' when compared to everyone elses with similar mods...ie paul, justin, and paradizzle all have similar mods (except para with the safc instead of the pfc) and are all around the 190-210rwkw mark :(

ramp rate (RR) being different will also alter the output figure.

higher ramp rate means the dyno pulls the car harder on the rollers, this can affect how the engine comes on boost, as more load means more boost. also the shootout mode can correct the figures accordingly

SHOOT4

SHOOT4F

SHOOT6

SHOOT6F

SHOOT8

SHOOTF

and so on, the F being forced induction turbo or supercharged.

so if your car was done in say SHOOT6 then you will get different results if you did your car in SHOOT6F and so on

At the last boostworx dyno day it was shown that the lesser shootout modes read slightly lower than the higher I.e Shoot4 vs Shoot81.

Looking through all the dyno sheets they are all within 5degree's of the AMB temp. I watched shaun place the IT sensor either in the cai snorkle or basically on the pod. HOWEVER.. Dyno runs were done with the bonnet up. So not really reflecting what would really occur on the street.

The way I see it is that if the IT is more than 10C higher than the AT, there is going be some good amount of correction involved. Infact that 'bogus' sheet shown before with similar AT/IT, thats the figures that would involve the least amount of SAE correction and thus a more 'real' result IMO. Anyone can get the temp sensor, throw it near the turbo manifold and get some bullshit results.

Before this thread gets hijacked ive got an update for those interested.

Took my car back to RE customs today to check it out again. We discovered the following. The timing on the car had been set to full advanced. The confusing part however was that the car was still running ok.

The problem is most likely to be either the timing belt was put on incorrectly and is out by a knob by my previous mechanic or the knock sensor is faulty or the wrong model.

Anyway, we reset the timing and moved it back a bit and we did another run on the dyno. For those of u non-believes the car still made 190rwkW and the AFR this time were areound 12.75. We did altogether 6 runs and the car did not ping or knock on any of the runs (altho i have been using octane booster lately)

Gonna take it back to Ray sometime next week to sort out the timing issue and if the timing belt has been installed incorrectly i am gonna lose it at my previous mechanic. At the end of the day however, i am basically driving around a 190rwkW basically stock skyline.... I guess it proves that the RB motor is one of the best responding motors to modification.

Your not running an adj. cam gear? This will throw the positioning of the cas sensor out.

Maybe the incorrectly set cam timing has helped power a tad. :wave:

Wouldn't it suck if you dropped it back to find its lost power everywhere and back to the norm.

I guess it proves that the RB motor is one of the best responding motors to modification.

How did it respond to modification if its stock?

Still dont see how 190rwkw is possible...its not really.

Did you check the ECU

Your not running an adj. cam gear? This will throw the positioning of the cas sensor out.

Maybe the incorrectly set cam timing has helped power a tad. :P

Wouldn't it suck if you dropped it back to find its lost power everywhere and back to the norm.

Nah its got stock cam gears... and yes it would suck :P ut i'd rather be safe than sorry

How did it respond to modification if its stock?

Still dont see how 190rwkw is possible...its not really.

Did you check the ECU

Its not completely stock, just lightly modded. Yea i checked the ECU it doesnt look like its remapped, i havent checked the inside of it yet. I reckon the timing is causing it to have this much power tho.

How did it respond to modification if its stock?

Still dont see how 190rwkw is possible...its not really.

Did you check the ECU

I dont see it possible either. See how it goes once all its little issues are sorted out (cam timing and afr).

If it still pulls high figures on stock boost then..................... get a run on a different dyno and if its still a high figure.............. well there's no explaination. :P

Its not completely stock, just lightly modded. Yea i checked the ECU it doesnt look like its remapped, i havent checked the inside of it yet. I reckon the timing is causing it to have this much power tho.

But you said you reset the timing and it still made 190...so it can't be the advanced timing...

You wouldn't be able to tell from the outside of the ECU if its been changed at all...

Maybe get a dyno run on another dyno just to see what that comes up with...or take it to the drags and see what mph you get...someone on here could work out rough power based on mph

hehe, i wasn't questioning the dyno or the operator...shit, im going there tomorrow so that wouldn't be a wise choice if i dont have faith in the workshop...

Just saying that in this case, its not a normal situation, so another dyno is just another option to get some ideas...chances are it will get a similar figure on the other dyno, then he can start crossing other shit off the list :P

Yea, atm i dont really care about the power figure, dont get me wrong, I'm like really happy, (less than $1000 spent and ive got 190rwkW) but im more worried bout the AFR. I reckon once that is fixed it'll go back down to 180... which is still pretty good for my mods, and not that unusual.

Dezz post up ur results when u get ur run 2moro. Good luck for getting 200rwkW, i will be very interested to see - my car has basically the same mods as u minus powerFC which I will hopefully be getting before Xmas.

IT & AT should be relatively the same for a turbo car

the DD "correction" is way off. The massive possible changed between cooler setups, boost levels/turbo efficiency etc can never be allowed for by some "software"

Remember the I/C will cool the charge, if its 55, its gonna be lower by the time it reaches the motor.

Closer to ambient is best

cheers

I'm still going to call botched figures.

Skylines simply don't make alomst 200rwkw standard.

As I said before, when my car was stock, it was in perfect condition, and by that I mean perfect. Motor was 169psi across all cylinders and 2% leakdown which is on par to brand new.

Made 140rwkw with 10psi and a full exhaust and FMIC.

210rwkw with powerfc added and 13psi boost, and toluene.

Dyno Dynamics Dyno.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...