Jump to content
SAU Community

Recommended Posts

Hey,

I'm looking at starting go-kart racing as I'm sick of doing nothing on my days off work.

Does anyone here race or could give some pointers about getting started up?

I am looking at probably buying an Arrow Kart, AX8 28-30

As seen here

And a Yamaha KT100S motor...

My only concern is that i'm quite tall (194cms) and not too sure about how I would fit.

If someone has some info on licences too than that would help.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/137012-go-karts/
Share on other sites

' date='2 Oct 2006, 06:17 PM' post='2546127']

Hey,

I'm looking at starting go-kart racing as I'm sick of doing nothing on my days off work.

Does anyone here race or could give some pointers about getting started up?

I am looking at probably buying an Arrow Kart, AX8 28-30

As seen here

And a Yamaha KT100S motor...

My only concern is that i'm quite tall (194cms) and not too sure about how I would fit.

If someone has some info on licences too than that would help.

Thanks.

Go straight to your local Kart Club for all your info!

As for the height ....... well it all depends on how supple you are. I'm 180 and had little trouble. Arrow make an extended front bar etc which shifts the pedals further away. If you go that route, you will need to buy the longer floor pan as well.

cheers

Muz

Link to comment
https://www.sau.com.au/forums/topic/137012-go-karts/#findComment-2555013
Share on other sites

  • 2 weeks later...

Mate you might struggle with the KT 100 engine better to go with electric start engine or get this one converted.

I am currently driving a 32 HP Biland twin cylinder 250cc 4 stroke and they are great fun or the smaller but stronger rotary engine which is 52 HP and 180 kg weight kart and driver plenty of brown pants moments in that little beast

post-28646-1161172789.jpg

Edited by tacker
Link to comment
https://www.sau.com.au/forums/topic/137012-go-karts/#findComment-2595172
Share on other sites

There is a dedicated kart forum here.. http://www.kartingaustralia.com.au/forum/index.php

As for the height, no idea, im the opposite end of the scale, over 1 foot shorter than you!

How much do you weigh is going ot be relevant to class. Also look at something which is raced competitively locally.

Licences are just a case of paying money. I think its cheapest in qld at $240 or $260 (one of the two)+ club membership. They are fairly expensive, but more comprehensive than a cams 2s or similar.

Once again chassis size (e.g 28/30 etc) will depend on class and height.

I wouldnt go rush out and buy brand new gear, just because a brand new S motor isnt going to be competitive without blueprinting, something used and proven might be better there. That said you would want something competitive and not some rubbish that someone is trying to offload on ebay.

Best bet would be to find a local kart shop or go to the track and talk to people.

Where are you locateD?

Edited by Turbo Tim
Link to comment
https://www.sau.com.au/forums/topic/137012-go-karts/#findComment-2596987
Share on other sites

And if you are going to get a used KT engine check the piston size as it may be up into its last size piston and then its a new barrel.

And make sure it is a sellect barrel or you are going to be a few hp down. If you can get it get very low port timing and close splits in the two port timings

Link to comment
https://www.sau.com.au/forums/topic/137012-go-karts/#findComment-2597017
Share on other sites

' date='2 Oct 2006, 06:17 PM' post='2546127']

Hey,

I'm looking at starting go-kart racing as I'm sick of doing nothing on my days off work.

Does anyone here race or could give some pointers about getting started up?

good pointers .1 dont start playing with karts .its like a drug and u will get hooked.

2 try it in the rain.

karts are mad fun . good luck.

Link to comment
https://www.sau.com.au/forums/topic/137012-go-karts/#findComment-2598797
Share on other sites

hey there i been racing for about 4 years now quite competitvely travelign to differnt major meets around aust id suggest you go for a class which would hav the most numbers, as the guy was sayign he races a biland depending where you are you wont get as many people racing id reccomend either the J class Senior national light or heavy or Clubman light or heavy i currently race in clubmant light as i belive its the most competitive classes out there or one of them. to date my best finish would be 6th in the 05 nationals in western australia, this is a pic of me in the wa states 3 weeks ago

post-25164-1161872728.jpg

Link to comment
https://www.sau.com.au/forums/topic/137012-go-karts/#findComment-2619092
Share on other sites

Karting.

Absolutely the most fun you can have without going insanely quick.

Have you driven a go-kart yet? It's totally different to driving a car (Thrown around, bumps etc)

If you're in Sydney/Wollongong area, head up to the picton race way.

Link to comment
https://www.sau.com.au/forums/topic/137012-go-karts/#findComment-2622363
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...