Jump to content
SAU Community

Recommended Posts

Hi all

I have recently installed a headunit to my R32 GTR and am now blowing the fuse for the dash lights/rear tail lights. Using this guide here: http://www.installdr.com/Harnesses/Nissan-Wiring.pdf I found that wire C had no wire in it, however wire B had a black and red wire, and I assumed they were swapped. Going on this assumption, I plugged up my head unit (The stock speakers arent actually that bad at all, how surprising is that?) and everything worked like a charm. Great I thought, put the car back together and went to test drive it to check for engine nose.

On powering up the car a slight problem dawned on me. Firing up my headlights, I noticed firstly that I had no dash lights, and secondly no tail lights (break and reverse/indictator works fine however). A blown fuse is what I guessed at and I scavanged a fuse from my old car (poor baby, shes so neglected these days). Lo and behold, as soon as I fired the head lights up, even with the car switched off and the headunit quite definatly off, the fuse blew again.

Anyone have any ideas as to why? Im out on my back here and have no idea wtf is going wrong, I really dont want to remove the head unit again as its quite a pain in the bum.

Thanks

Ian

Link to comment
https://www.sau.com.au/forums/topic/138804-dash-wiring/
Share on other sites

find the black wire on the radio and bolt it to the frame. the red/blk wire you have is the amplified antenna run that to the blu or blu/wht wire on your radio.

(I'm going to do a snip of this post and use it elsewhere.)

Link to comment
https://www.sau.com.au/forums/topic/138804-dash-wiring/#findComment-2587364
Share on other sites

hehe not quite, the remote wire in the main plug is for a power antenna whereas the remote for the stock amp seems to me to be in the rear speak plug on the 32 as well.

I could be wrong however :P

take a snap of the rear plug- i want to look.

Link to comment
https://www.sau.com.au/forums/topic/138804-dash-wiring/#findComment-2594513
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
    • Hello everyone, I am happy to join you.
    • Whereabouts are you, that looks exactly like Akira's old car....
×
×
  • Create New...