Jump to content
SAU Community

Using A Q45 Afm?

ix9

By ix9,
in Engines & Forced Induction

 Share

Recommended Posts

ix9 Grand Master

ix9

Posted
Posted

Hey Guys,

My AFM appears to be screwed, it will randomly drop to 0% while driving, or putting my foot down will make a sucking noise but do NOTHING until I release and re-apply a few times!

Checked the plugs etc.

The S-AFC-II says its going to 0% if I keep my eye on it, at random times :P

Is it possible to use a Q45 AFM to replace the stocker? ie with the use of my S-AFCII ?

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/139080-using-a-q45-afm/
Share on other sites
The Mafia Grand Master

The Mafia

Posted
Posted (edited)

nope, the q45 is HEAPS bigger than stock, so you'll need some form of adapter.

Get a z32, its a direct replacement.

How do I know? I'm using a q45 :laugh: But on a Garrett GT30..

Edited by The Mafia
Link to comment
https://www.sau.com.au/forums/topic/139080-using-a-q45-afm/#findComment-2590498
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

im using one too.. GT3582R - you can get the apexi power flow pods which have the bolt pattern for the A45. see KUDOS motorsports - he is sponsor on here. great guy awesome service. I just got a setup from him because.. ummmm.. lets just say i ran over my Q45 AFM and POD. Long story =)

Link to comment
https://www.sau.com.au/forums/topic/139080-using-a-q45-afm/#findComment-2590516
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

Super cold air induction.. :laugh: AFM and filter was sitting in the air scoop of front bar. it bottomed out and got run over... Dont laugh.. someone on here had it happen to them and I laughed at them :huh: bad karma

Link to comment
https://www.sau.com.au/forums/topic/139080-using-a-q45-afm/#findComment-2590661
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Ball bearing turbos

      By sunsetR33 · Posted

      Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • GTSBoy
      R33 GTST Axles

      By GTSBoy · Posted

      There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • thozza
      Intro/R33 owner

      By thozza · Posted

      Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Lithium
      Forced Performance Hta Turbos

      By Lithium · Posted

      Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...