Jump to content
SAU Community

Recommended Posts

Well the PNV seems to have developed a few problems in recent times. Why is it that things seem to go wrong when you are trying to sell?

Anyway here they are:

1. Clutch is not holding pressure. I can pump it up and it will work while I drive. Let it sit for a day or so and the pressure is gone again and have to pump it up. It doesn't seem to be losing any fluid and can't see any visible leaks, so not sure what is going on.

2. One of the headlights has gone dim. I have been running 90/100's on the low/high. First the left side one went dim. Next time I turned the lights on it blew both fuses, replaced them, blew them again. Replaced globes with the ordinary spec(55/60s?) and fuses and it seemed to be alright for a while. Now the right hand side one is dim all the time. Its dim on both low and high beam. New fuses make no difference. Points to a possible earth problem, loose or burnt connection?

Any ideas guys?

Link to comment
https://www.sau.com.au/forums/topic/139125-few-problems-that-i-need-help-with/
Share on other sites

Well the PNV seems to have developed a few problems in recent times. Why is it that things seem to go wrong when you are trying to sell?

Anyway here they are:

1. Clutch is not holding pressure. I can pump it up and it will work while I drive. Let it sit for a day or so and the pressure is gone again and have to pump it up. It doesn't seem to be losing any fluid and can't see any visible leaks, so not sure what is going on.

2. One of the headlights has gone dim. I have been running 90/100's on the low/high. First the left side one went dim. Next time I turned the lights on it blew both fuses, replaced them, blew them again. Replaced globes with the ordinary spec(55/60s?) and fuses and it seemed to be alright for a while. Now the right hand side one is dim all the time. Its dim on both low and high beam. New fuses make no difference. Points to a possible earth problem, loose or burnt connection?

Any ideas guys?

sound like the clutch master cylinder is poked. New seals or a complete new one is required.

The other one sounds like yourve cooked your wiring. 100/90 are nearly double the current draw over a 55/60 close to 15amp's compared to the nomanal 10amp. Id say check all your wiring, follow it back im sure there will be a melted patch. If you wish to run higher wattge bulbs best to install a secondary loom kit and relays and feed them directly off the battery, Work well for me. 100w/130's and 100w high beams work well :)

sound like the clutch master cylinder is poked. New seals or a complete new one is required.

The other one sounds like yourve cooked your wiring. 100/90 are nearly double the current draw over a 55/60 close to 15amp's compared to the nomanal 10amp. Id say check all your wiring, follow it back im sure there will be a melted patch. If you wish to run higher wattge bulbs best to install a secondary loom kit and relays and feed them directly off the battery, Work well for me. 100w/130's and 100w high beams work well :)

I'll go with stagefumer as far as your clutch goes, I had the same problem when mine sat for 3 years in the garage.

It wasn't such a biggie for me as I was replacing the slave cylinder in any case.

For anyone that wants to know and is using a heavier weight clutch plate diaphram the VL uses a 7/8 (22mm) slave cylinder as opposed to our 3/4 (19.05mm) More fluid, less pedal pressure and easier on the legs.

I have an auxilliary harness for mine, it's got written on it "Bosch System Harness" and as per pic, it has it's own relays for each bulb and heavier gauge wiring. I'm going to use it with Rallyart 170/130 H4's and IPF 130 H1's.

What happens when using high power globes, the heat generated by the power draw from the globes, is too much for the standard wiring, as it's not designed for them. Maybe if you source low input high output globes, like designed for the new style polycarbonate headlamps used in some cars today they will fix your problem. But if the heat generated has already burnt the wiring, take it to an auto elec and get him to rewire heavier gauge wiring across the headlights and your problem should be gone.

Cheers, D

I'll go with stagefumer as far as your clutch goes, I had the same problem when mine sat for 3 years in the garage.

It wasn't such a biggie for me as I was replacing the slave cylinder in any case.

For anyone that wants to know and is using a heavier weight clutch plate diaphram the VL uses a 7/8 (22mm) slave cylinder as opposed to our 3/4 (19.05mm) More fluid, less pedal pressure and easier on the legs.

I have an auxilliary harness for mine, it's got written on it "Bosch System Harness" and as per pic, it has it's own relays for each bulb and heavier gauge wiring. I'm going to use it with Rallyart 170/130 H4's and IPF 130 H1's.

What happens when using high power globes, the heat generated by the power draw from the globes, is too much for the standard wiring, as it's not designed for them. Maybe if you source low input high output globes, like designed for the new style polycarbonate headlamps used in some cars today they will fix your problem. But if the heat generated has already burnt the wiring, take it to an auto elec and get him to rewire heavier gauge wiring across the headlights and your problem should be gone.

Cheers, D

Hi all , when I had the DR30 I spent a few afternoons at Pick n Payless cutting into headlight looms on MR30's . It was very obvious that the Australian delivered cars had heavier gauge wiring than that DR30 did . I'm not sure what a PNE would have but its worth a look to find out .

Nissan went to a lot of trouble to make the high low system work off two relays and operate the gauge lights as well . Mine carried the full current across the stalk switch as well which is not flash . At the time I think I worked out that it really needed 6 relays switched by the std loom to make it all work (dash as well) ie one for switched earth on each side and one each for high and low beams on both sides . Standard they are quite involved .

I would also take a close look at the reflectors in each light because the age of the things makes them a bit suspect . The Iron Mask lights have a bad habbit of damaging the chrome plating near the bulb making low beam a bit dull . There are supposed to be mobs around that can replate them but for the non Iron Mask lights good seconds are probably still around . High wattage bulbs put out a lot more heat so be sure the light unit can cope with this .

Cheers A .

Thanks for the ideas guys will have a look into it all.

Is there any easy way to tell if the clutch master just needs new seals or a whole new one?

I know running the bigger globes wasn't a great idea, but it was a good easy fix that lasted a far while really. Am now going to have some fun taking of the stuff that all the wiring is in to find where the problem is.

At a guess it wont be your master cylinder I would say its your slave cylinder as ive seen heaps of them stuffed on R30s before, but I may be wrong! Last time I brought a slave cylinder it cost around $25 and I got a master cylinder priced up at the same time and they wanted $45 thats NZ prices remeber though!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...