Jump to content
SAU Community

Gtr Bar On A Gts-t

32DET

By 32DET,
in Exterior & Interior Styling

 Share

Recommended Posts

32DET Enthusiast

32DET

Posted
Posted

I have been told that if i buy a genuine r32 GTR fornt bar for my gts-t it wont fit properly. So will any fibreglass copy be fine or do i need to make sure that the replica bar is made purely for gts-t's. If it has to be specially made do you know anyone who does this as when i look at replica GTR bars for sale it doesnt state whether its for a GTR or GTS-T...cheers for any info.

Ryan

Link to comment
https://www.sau.com.au/forums/topic/139663-gtr-bar-on-a-gts-t/
Share on other sites
tiesto Proficient

tiesto

Posted
Posted

i've got a gtr style front bumper made from eastbear which fits my gtst. but its cracked so im looking to replace it with a proper gtr style with the n1 holes and also the smaller numberplate holder so i can sidemount the numberplate

the best one i found so far is from jetspeed.com.au...

anyone got any other ideas where i could get a bar from?

180mph, im suprised your genuine gtr front bar fits your gts-t? do you have a r32 gtr intrusion bar aswell? what else did you do to make it fit?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      R34 GTR Speedo Drive , sensor type ?

      By Butters · Posted

      Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...