Jump to content
SAU Community

Recommended Posts

You heard it. Morpowa, Saturday 17th May, 8.30am kick off. $35 bucks a head. Got some good interest so far, and even better the dyno is being calibrated by Dyno Dynamics this week to be 100% accurate for the event.

Matt, if youre up to it you want to help me organise some numbers? Cheers.

LOCATION:

MORPOWA

14 FAMECHON CRESCENT

MODBURY NORTH

SAU ENTRY LIST:

Nightcrawler - S15

MattR - GTS-t

Freebaggin - GTS25t

PHAT 33 - GTS25t

grepin - GTS25t

Nozila - GTS25t

Busky2k - S14 200SX

  • Replies 130
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by Martin Donnon

Matt, if youre up to it you want to help me organise some numbers? Cheers.

Yeah sure mate :P I'll sticky the thread for starters.

I also have a few mates that would be interested in taking their cars on the dyno so if that ok with u i could get about 4-5cars there.... if u can tell me how many cars u are looking for on the day i could try and get some numbers for u...

thanks

If I get it, put it down as a hybrid and its white. Hey andrew those mags you were looking at where were they. If I get this new car I will be selling the 18s that are on it and gettin something else. Cheers Matt

i will try to bring:

2 - Soarers twin turbo (1 is limted ed. but i dont think any internals are different)

1 - 180sx

Another thing is that im on the southern side of adelaide so i'll have 2 try and figure out a way transporting them.

I also have 2 confirm my mate's cars but should b able 2 get at least

1- R32

1 - 180SX

1 - S15 Sil80

all the cars are faily stock, just usual mods like a/m air filter, exhaust... nothing too crazy.

I'll tell u the definate numbers as soon as i can.

thanks

Hip,

Every dyno day I've been to each entrant has had at least a couple of power runs (2-3). So you'll get a chance to do a low boost run, & then a high boost run :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...