Jump to content
SAU Community

Recommended Posts

Finally got my car tuned properly after i found the problem...it was nothing but a leak in my BOV. Before the problem the car was making 175 rwks. after we fixed it, it made 205 kws and once 207rwks. Picked up 30kws cos of that little problem. Thought it mite have been a block cat so i took that off, it wasnt it. Checked the afm, wasnt it. checked if one the blades had come off the turbo and it wasnt it. checked the lines on the boost controller. finally checked the bloody BOV.

Car: 1993 r33 gts-t

Mods: FMIC, BOV, blitz EBC, pod, slpit dump/front pipe, high flow metal body cat, Cat back exhuast, power FC and walbro 500hp fuel pump. tuned at just under 12psi.

post-29367-1161936033.jpg

post-29367-1161936074.jpg

Link to comment
https://www.sau.com.au/forums/topic/140673-finally-tuned-and-the-results/
Share on other sites

thanks mate

no it was inside the bov itself. just inside the trumpet, there was a little black thing, so he pulled it off and it was just a rubber seal. i cant tell you nemore, but yeh after that it was fine. i remember before that, i was only starting to build boost at 3000rpm and full boost by 4000. now its boosting in the low-mid 2000rpm and close to full boost somwhere around 3000-3500 rpm. Yeh top end feels better, but mid-range grunt is more surprising.

shouldnt it be making more? you got management etc, i made 196kw on 14psi(with an 18psi spike mid run) mods are same as yours except no cat and no pfc. this is on a rb20 with a suspected vg30 turbo im not trying to put your car down, its just i see these figures and wonder why my very very mild rb20 is up around the level of moderate rb25's

Edited by dead32
shouldnt it be making more? you got management etc, i made 196kw on 14psi(with an 18psi spike mid run) mods are same as yours except no cat and no pfc. this is on a rb20 with a suspected vg30 turbo im not trying to put your car down, its just i see these figures and wonder why my very very mild rb20 is up around the level of moderate rb25's

put it this way, standard trubo rb25det's max power is around 210rkws. A lot of people with the same mods find their power varies between 190-210 rwks depending on a number of factors: dyno, condition of turbo, engine, etc etc. You say you made 196 kws. now you arent too sure on what turbo u used. if you say its has vg30 housing running 14psi is fine and on a rb20det that power figure sounds about rite, but remeber im only running 12 psi becuase its a standard turbo. Also its not just the max power thats important. Ive noticed more power across the entire rev-range.

Edited by moonus
shouldnt it be making more? you got management etc, i made 196kw on 14psi(with an 18psi spike mid run) mods are same as yours except no cat and no pfc. this is on a rb20 with a suspected vg30 turbo im not trying to put your car down, its just i see these figures and wonder why my very very mild rb20 is up around the level of moderate rb25's

What makes you think its a VG30?

The R34 and VG30 turbo's are identical from the outside, the difference being the vg30 runs the small rb20 compressor wheel where as the r34 turbo runs a big motha comp wheel. There is a tip to identifying the sound of one... The VG30 spools quieter, more like a little buzz where as the RB20 and rb25 turbo's are louder and have more of a whooshing sucking sound, the reason for this is their comp cover inlet design.

Essentially from greatest power to less...

1. R34 GTT Turbo

2. R33 Turbo (Series 2 turbo's make same power just spool a little better)

3. VG30 Turbo

4. RB20 Turbo

And if your after maximum response with an ever so slight trade off in peak power... The R33 Series 2 turbo. Will still make up around 190rwkw on 14psi.

Don't be thinking if you throw a pfc in to yours you will make more peak power.. It won't, where you are at is where it will approximately stay. It will however pick up mid range, spool slightly earlier and be quicker simply because there is greater average power. How often are you at your peak power rpm compared to the rpm accelerating TO that peak power rpm. :sick:

EDIT: I see Steve is lurking around SAU quite a lot lately... Are you thinking about jumping back in to a Skyline Steve? hehe :sick:

ahh i get cha moonus, as for you post cubes, i was told by the previous owner it was a vg30, the turbo is deff not quite, it sounds like a realy high pitched whine, going by the boost spike/drop off, on my dyno run's im assuming the turbo has reached its efficiency level, therefore making good boost mid range but unable to flow it at high rpm, with same boost but larger injectors and a pfc i would assume with a deccent tune it would have to make 210-220? or am i dreaming?

ahh i get cha moonus, as for you post cubes, i was told by the previous owner it was a vg30, the turbo is deff not quite, it sounds like a realy high pitched whine, going by the boost spike/drop off, on my dyno run's im assuming the turbo has reached its efficiency level, therefore making good boost mid range but unable to flow it at high rpm, with same boost but larger injectors and a pfc i would assume with a deccent tune it would have to make 210-220? or am i dreaming?

I'd say it may just make that power... but at the end of the day it's still an RB20, so it's not really worth the trouble IN MY OPINION.

BTW, I made the exact same power (196rwkw) with an R33 series one turbo and chipped ECU, so your power output is pretty much the norm

went in this car yesterday!!! amazing difference the power fc has made all round...nice & smooth, barley any lag (compared to before) & pulls hard right through rev range...with traction & a bit of practice should easily get under a 13.5 all day long

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...