Jump to content
SAU Community

R33 Trust Style Front Bar (series 1) Touch Looking! - $280

mikymouse
 Share

Recommended Posts

mikymouse Rising Star

mikymouse

Posted
Posted (edited)

I have for sale a Trust style front bar. It was fitted to an R33 Series 1 previously and fitted perfectly (as shown). This is unlike a new front bar which you will buy and have to spend more money getting it cut and fibreglassed to fit properly.

It has been sanded back and is ready to paint. The bottom of the bar has minor crack, which will need to get either bogged up or glassed. This is a minor job.

If the bar doesn't sell now, I will fix the crack and primer it and readvertise.

PRICE: $280

Pickup ONLY. WESTERN SUBURBS OF MELBOURNE.

frontbar1.JPG

frontbar2.JPG

frontbar3.JPG

frontbar4.JPG

Edited by mikymouse
R33_KRAZY Rising Star

R33_KRAZY

Posted
Posted

hey mate,

keen as but my front barhas seen better days.. my grille is fine an bumber is in 1 piece but has been patched up b4 an is just a little bit rough.. its black also

  • 2 weeks later...
mikymouse Rising Star

mikymouse

Posted
  • Author
Posted

For something like this one, you can get away with putty. However if you have a large crack or something that will crack again without reinforcement, you will need to use fibreglass.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...