Jump to content
SAU Community

Mickey Thompson Drag Radials New 255-50/16 $220ea

caz
 Share

Recommended Posts

caz Enthusiast

caz

Posted
Posted

I have only 2 of these tyres. They are classed as blemished due to 2 letters on the sidewall being smudged during manufacture.

P9160002.jpg

*pup is not included :) *

I can arrange freight to Bris, GC, Melb, Syd at reasonable cost or can arrange pick up WSID or Wollongong.

Caz..

Caroline Felgate

0411021823

[email protected]

I am in Thirroul, near Wollongong.

caz Enthusiast

caz

Posted
  • Author
Posted

Not love nor money would buy that boy :)

He's absolutely magic, my sons Amstaff, Chopper. 13 weeks

He even rides a skateboard, ALWAYS wanted a dog that could do that :huh:

PA030006.jpgP9110003.jpg

PA030010.jpg

PA030013-1.jpg

You could buy a car for what my son paid for him..... :):huh: LOL

how much for the dog?
Z24O Rising Star

Z24O

Posted
Posted
Not love nor money would buy that boy :)

He's absolutely magic, my sons Amstaff, Chopper. 13 weeks

He even rides a skateboard, ALWAYS wanted a dog that could do that :)

PA030006.jpgP9110003.jpg

PA030010.jpg

PA030013-1.jpg

You could buy a car for what my son paid for him..... :):D LOL

......i'll give you $50 for him in six months time when he's dug a hole in your backyard the size of a swimming pool,lol.

siddr20 Grand Master

siddr20

Posted
Posted (edited)

damn wish the money.. Goin to the drags next week, and this would have been handy!!

Has it been sold??

Btw what type of dog is that??

Edited by siddr20
caz Enthusiast

caz

Posted
  • Author
Posted

Im going to the drags tonight >_<

I had 3 people all wanting them so I went in the order they replied. I will give Anita till tonight to confirm or I will offer them to next and so on.

Pup is an Amstaff, from Andonas Kennels

American Staffordshire(American Pitbull in USA)

Cheers,

Caz.. :woot:

damn wish the money.. Goin to the drags next week, and this would have been handy!!

Has it been sold??

Btw what type of dog is that??

  • 6 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...