Jump to content
SAU Community

Recommended Posts

Ok heres there story.

I tried to install my pioneer cd deck into my R32 GTS-t.

Me and a friend have done many stereo installations before.

When we first installed it, we blew a fuse that controlled the dashlights/tail lights.

Thats ok, we found the culprit wire(s) and sorted that out. No more fuses blew.

From then when I turned my car off, the doors would lock and when I clicked the button on the immobiliser, it would unlock and re-lock again.

So we ripped the whole deck out and detached everything from the wires. So now there is no wires connected to anything. When i turn my car off, it unlocks the doors. So i will hop out, lock the doors and go. Now when i return to my car, the immobiliser is armed, i click the button and it will unlock the doors and then lock straight away. The only way to get in, is to use the key.

When the immobiliser is not armhated, the doors will lock fine.

I have spent many many late nights and very many hours trying to solve this problem. We went through and pulled apart all the relays and tested them. We also swapped over the immobiliser with a friend (same type) and the problem was still there.

So our guess is, there is some wire(s) that were connected to the back of the stereo that either need to get power or need to be ground.

Another point is when you click the immobiliser button, it doesn't flash the parkers/tail lights like it use too.

Can anyone provide any help on this?

I have gone through most of the wiring and i know what most of the stereo wires do. However there are still wires there that we don't know the exact purpose for.

Any help would be greatly appreciated.

Yes, thats an option.

But those guys are ****ING DODGY!! and i mean very dodgy.

When we were going through my car, we found wires spliced and left like that. Things butchered here and there.

Guy i work with decided to get them to do his tint.

They ripped the back shelf out, and wrecked all the terminals. Also broke the shelf. At first they claimed they never touched the shelf, then they said, they just pulled it forward a little.

They're not someone i would like to trust or do business with.

Go through all the fuse's with a test light and ensure that they are all ok, next check that all earth wires to the alarm module are grounded

(HINT: some alarm installers use the radio as a ground)

some alarms use a seperate module for the door locks check this aswell.

When i fitted my alarm I used the wires going to the hazard switch did you plug it back in? as mine would not flash if the switch was not pluged in.

Thats all I can think of for now check all of the above and let us know how u went.

if u have more info that would help me tell u what to look 4!

Thanks for the offer rob, but i'm in WA :D

DAMQIK, Done just about all the checks you can think of.

I though i posted everything in the first post, please let me know what i missed out.

It doesn't have an alarm. Factory central locking and a Cyclops paralyser immobiliser.

I have a mate who was an auto elec for a few years, i'm trying to get him to have a look, but hes just been busy.

Soon as i sort the prob out, everyone will know!!

Thankyou everyone for your imput.

Ok so you checked the fuses under the dash? under the black cover under the bonnet & next to the battery? (there are 3 Fuse boxes in a r33)

PM me your email address and I will send the wireing diag 4 jpg pictures.

Thou I feel your prob is bad earth maybe run a new wire from earth to the module and the same for power+ if you have not yet tryed this.

is your cig lighter getting power?

Ok, I feel like a dick.

All along i knew the problem was easy, but just kept missing it. Mainly because each time we were working on it, it was between the hours of 10pm-3am.

There is a relay down in the kick panel with a "door lock timer" module, somebody has taken a wire off that relay and put it back on the wrong terminal, plus the immobiliser had a blown fuse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
    • @dbm7 and @GTSBoy thank you both very much! will give that a shot!
×
×
  • Create New...