Jump to content
SAU Community

Recommended Posts

Thanks heaps guys, if only I had the money.

I was talking to somone in an Import shop (not giving away names) and they told me that the Autech R33 sedan was not able to be complied in Australia because controlled crashes have not been performed on them. Is this true???

Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2660665
Share on other sites

HPI had a story on a black skyline 4 door that had a gtr conversion - this is probably the same. Still, if someone is keen, they should check it out - if its done properly it might still run well.

I'm pretty sure it was in speed magazine, not hpi though i could be wrong.. Pretty sure its the one out of the mag..

Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2661245
Share on other sites

Its not real, thats the one Ernest Parry built a few years ago and yes it was in HPI. Its still missing the few touches that make a R33 GTR sedan different - ie series 3 xenon lights, interior etc. A propper Autech R33 4 door goes for much more than what he's asking.

Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2662778
Share on other sites

there is a ture one up at mooloolabah I have seen it parked there a couple of times but never find the owner :D

is this what u are talking about.....

there is a proper impul version up here yes, had the plates 25.MAT on it, been for sale for ages, but its not a GTR its only a 4 door impul version. with a few tasteful mods.

he has been a member on this site ages ago but havent seen him around for a while.

now doesnt have the plates, only has standard ones on it, i see it most days going to work.

here is a link to it for sale.

http://www.carsales.com.au/pls/carsales/...p;category_id=3

Edited by 85URK
Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2667983
Share on other sites

Ok he just got back to me. It has been made from an R33 V-spec GTR with Autech parts, flared rear quarters and door. Made by Skyline Imports QLD.

VIN is 6U9000ENR33005578

Booya,h yeah I was 99.9% sure it was his old one, used to see it a fair bit so knew the trim/wheels.

Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2673321
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
    • And now the bloody flapper is jammed slightly open. Lazy as all f**k in 3rd-5th (very hard to convince it to make much boost before you run out of revs), but will make 12 psi in 1st, which shouldb't be possible with a 5 psi spring and controller set to <10 psi. Methinks I'm lucky it jammed where it did, rather than fully closed. It's actually a well weird situation. Careful examination of what's happening in the back of that housing when the gearbox comes out and all the other stuff (injectors, AFM retune) is supposed to be done, next week.
    • The powder coating came in at $250 EACH. The TRX rims got a coat of clearcoat on the outside only.    
    • Bit wet, but YUMMY
×
×
  • Create New...