Jump to content
SAU Community

Recommended Posts

I took by rear bar off yesterday to fit a tow bar and found a little rust it hasn't done any significant damage yet and I think I should be able to fix and stop it ok.

My car is a 95 R33 GTSt 4 door with 70,000, Never bent and in visualy perfict condition.

I just thought I would let other R33 owners know about the problem so they can check there cars.

To see the problem you will have to pull the rear bar off.

1.

Remove number plate and undo the bolt that holds the bracket down.

2.

There are three nuts on the inside of the boot on both sides behind the trim and below the taillights you will need to remove these from both sides.

3.

With the boot open there are I think 4 maybe more black plastic plug type clips that hold the top of the bumper on they will need to be removed.

They are a bit tricky I tried levering them out with a screw driver but ended up having to use pincers and just pulled them up until they popped out (I only cracked one)

4. Now you should be able to pull the bar off.

The problem area

There is a upside down L shaped bracket (The one the black plastic plug clip things go into).

On my car there is rust stains that have leached down from behind this and a few bits below it where the paint is bubbling up. It looks like moisture has got in between the bracket and the back wall of the boot.

I recommend all R33 owners check this spot, before I pulled the bar off I had no idea my car had any rust. :P:D

Has any one else had this problem?

Are there any other Rust Hot Spots I should know about?

Any Recommendations on how I should go about fixing it ?

Thanks

also big rust spot

is under the spare tyre in the boot

i got a leaky boot so water has collected down there and its starting to rust

can someone help me with this leaky boot business?

its in my other thread

I own both a VL Calais turbo and a Skyline.

What’s wrong with a tow bar on a skyline?

I’m not wanting to tow a horse float just a aluminum motor bike trailer and two bikes a total of 350 kg.

Skylines can tow fine I have seen them towing boats and one with a small pop up caravan. R33 GTS-t 4 doors have a towing capacity of 900 KG

Hi Burns,

After taking the front right hand gaurd off my car, and the right side skirting, there if a gap near where the skirting is screwed onto, at the front. Which has succesfully stored about 3 handfuls of dirt / leaves for the last few months at least.

There were signs of minor surface rust, nothing major, but I am definatly glad I found it now not later :D

I'd reccomend taking the skirting off both sides and giving it a good clean. Especially at the front near the framework.

The VL is for sale

The tow bar on the skyline cant be seen any way it is all hidden behind the bumper except for the tong bit and I will take that off when not using it.

Thanks for the tip glenmcrae I will have a look while the car is all pulled apart.

The tow bar came from Nissan it is a S14 200sx tow bar and cost me $265 with all the bits and pieces.

I was also quoted $395 for a custom one.

I was told the S14 kit from Nissan will fit on the skylines fine and it almost dose the only problem is that there is a bulge in the lower section of the rear boot wall. this bulge stops the tow bar mounts from sliding all the way in to the chassis rails so I will have to have them extended about 3 inches. My car is a 4 door the 2 door might not have this bulge so it will go or piss easy.

  • 11 months later...

about the leak into the boot issue - if your car is parked on a down hill slope, water pools just under the boot lid (where it is supposed to run out, but on a downhill slope cannot go anywhere). The pooling water slowly leaks through a join in the metal. Hope that helps to explain it.

Well thats where mine leaked.

Mike

The tow bar came from Nissan it is a S14 200sx tow bar and cost me $265 with all the bits and pieces.

I was also quoted $395 for a custom one.

I was told the S14 kit from Nissan will fit on the skylines fine and it almost dose the only problem is that there is a bulge in the lower section of the rear boot wall.  this bulge stops the tow bar mounts from sliding all the way in to the chassis rails so I will have to have them extended about 3 inches.  My car is a 4 door the 2 door might not have this bulge so it will go or piss easy.

Burns,

Mate I would be very interested to see if you could take any photos to share of the tow bar on and off. Interested to see what it would like as this is something that could come definately in handy for me, and I am sure some others would be curious to see what it all looks like. Always another option and something to do.

Cheers mate!

-Alex

  • 10 months later...
Tow bars on a stock r33 turbo would be fine. But once u start playing with mods, the way the power come on aint the best for towing as u could easily rip the ass end out of the car when boost hits.

Thats exactly what I was thinking... but on a 4 door N/A R33 it would look sorta ok.

yeap under the spare tyre is the worst area but the problem infact is caused by the tail lights, the sealent on the taillights have worn out and leaks water into the interior of the boot, and hence the water finds its way under spare tyre wat i did to remove the leak was pull out both rear lights, done easily from the inside of the boot, unplug the wires take out the screws and push the lights out, then find a good sealant from an autoshop and reseal it , but make sure that u clean out the junk of the old worn out sealant 1st, its disgusting, but u will find after applying the new seal there wont be nemore leaks :P and u can easily fix the rust

Another R33 rust area is around the drivers side window wiper shaft, just as it comes out of the cowling under the black plastic escutcheon There is an indentation around it with no way for water to drain. I had to drill out one of the bolts that secure the shaft to the cowling as it was rusted and seized. A small hole drilled in the depression will fix it....

  • 1 month later...

Best rust treatment i know of is cold galv, but kill rust does the same job with a gloss finish, dont know if it comes in a spray though. I usually clean off rust spray cold galv then with a matching gloss

Another spot for rust is the engine bay chassis rails there is a folded sheet that runs along the top and rust gets between seen this on a import that was rejected because of it. They cut out the chassis no. and took all the id plates.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • 🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day   Highway gets as low as 10l/100km on my end so I'm not as worried about it being a mechanical issue. More likely just the tune on the haltech.
    • While I was waiting for the new parts to come in for the charge pipe and radiator I decided to do some turbo modification. The drive pressure (exhaust backpressure) was a lot higher that I thought it should be. For 32lbs of boost drive was 55lbs. The turbine housing is a 1.10AR and my turbo builder has suggested to go to a 1.25AR. To test if a larger AR would do anything to reduce drive pressure AND not spend any money I decided to hog out the divider in my current housing. I removed it from the inlet and the whole way through the housing.  After reassembly and testing it doesn't look like this modification did anything for reducing drive pressure or requiring more fuel (making more power). Oh well, it was worth a shot. We'll get some data at the track if it makes it past the 60ft. I also machined a $7 shift knob off Amazon to fit my Stillway shifter since I didn't like the Stillway shift knob. Next on the list was the radiator replacement and fabrication of a new intercooler tube that had no silicon coupler. No pictures of this - I was short on time each night after work to get this done and didn't stop to take pictures.  Next was to get the clutch disks out and replaced. Previously when installing the dogbox I had ordered a set of the same sintered iron disks I had been running because I switched to the 26-spline input shaft. I thought it was odd that they didn't have any markings or brand name on them like all my old disks had but installed them anyway. At the track I could not get the clutch to lock up using my normal strategies. After two track nights I reached out to the clutch manufacturer and ask their thoughts. They said they had to switch the material out because they were having trouble getting the original material and that this new material would not take to being slipped very well.  So out with the first set of 26-spline disks and in with the correct material 26-spline disks. While I had the trans out I added an inspection/service hole. I've wanted one of these for a while. Now I can have a look at things and change the front cover shimming when needed (clutch wear). I hustled and got the clutch change done in a few hours on a Saturday. Hopped in the car and drove home. On the way home I did a 1-3 pull. When shifting from 2nd to 3rd the core plug in the back of the cylinder head popped out and dumped all the coolant. Thankfully I was only 30 seconds from home and coasted it there. Datalog showed nothing unusual and 2.5psi of coolant pressure. That plug has been in there since 1992 but I guess it worked its way out. Pulled the trans AGAIN and replaced the plug, JB welded it in, and made a brace. Also deleted the head drain I had added in during the bearing issue fiasco.  I am currently changing my boost control plumbing to make it cleaner. After that is done I'll make another attempt at getting past the 60.
×
×
  • Create New...