Jump to content
SAU Community

Recommended Posts

Obviously you want something fully synthetic- I always use mobil 1, but hear that the top end Motul stuff (6100 or higher, like 300V?) is also very good.

People always complain that its too expensive when doing frequent oil changes, and that you can use cheaper oil because of the fact that its changed frequently (which does sound logical).

But its your engine, and the oil you put in it is all its got, why not give it the best :P

Also i suppose it depends how you drive it. If you redline it all the time, definitly go a good oil like the mobil. If you just cruise/potter it around i dont suppose it would really matter!

While on the topic of oil, can someone explain WHY turbo engines need synthetic oil!?

Cheers, NACHO

Yeah, I use Mobil 1.

I think synth oil can take the heat from the turbo better.

Also synth oil starts to break down at around 125-130 degrees, while the cheaper stuff breaks down at lower temps. That and the fact that the synth has better cold and hot lubricating properties.

J

Go Motul. I changed to 300V at the last change and it feels really good. 2000K and it is still like new, oil is still clear.

If you take the old oil down to the local servo (with mechanic of course, no point taking it to shell select!) and give them 5 bucks i'm sure they can get rid of it for you :)

Guest Oz Elitesport
Originally posted by Xeron

10w-60, u got a bad smoking or leak problem, cause if u dont get a lighter weight, check ur manual for what is recommended for ur areas temperature range, but ull be loosing a few horsies with that oil being so heavy when warm.

I'm using the castrol formula R (10W-60).

This has been recommended by others. Dont have a bad smoking or leaking problem, just took the advise of others.

Oz.

Castrol says this about their Formula R 10W-60 oil:

A full synthetic 10W-60 viscosity engine oil that ensures maximum protection under a wide range of driving conditions and high stress applications. It helps extend the life of your engine as well as minimise oil consumption. Originally developed for endurance sports car engines, it is recommended for highly stressed competition engines and older technology sports cars and luxury sedans.  

SAE 10W-60, API SL/CF, ACEA A3/B3

About the 5W-30 oil they say:

A synthetic 5W-30 viscosity engine oil which enables faster acceleration with excellent engine protection and performance. If offers excellent engine cold start responsiveness and contributes to increased fuel efficiency. Recommended for highly tuned, four cylinder engines and latest technology engines requiring 5W-30 or 10W-30 viscosity. Approved for use by Porsche, VW, Audi and Mercedes-Benz.

SAE 5W-30, API SL/CF, ACEA A3/B3/B4

And the 0W-40:

A full synthetic, free flowing 0W-40 viscosity engine oil that significantly reduces friction, whilst delivering more power, greater protection, reduced emissions and superior fuel efficiency. Recommended for the latest technology and prestige engines, such as Porsche, BMW, Rolls Royce, VW, Audi, Jaguar, Rover and Mercedes-Benz.

SAE 0W-40, API SL/CF, ACEA A3/B3/B4

I can't remember exactly, but I *think* the owner's manual specifies 10W-50 grade oil. That would make the 30 and 40 weight oils a tad too thin. I'll have to check the owner's manual when I get home.

All of these Castrol synthetic oils are of very good quality though so it may not matter too much. Either way, I'm presently using the 10W-60 stuff and I have absolutely no bad things to say about it. The car doesn't use a single drop between oil changes.

If you're changing oil regularly and often, it shouldn't really matter which brand you choose. Just get a good quality fully synthetic oil and you'll be ok. I personally chose Castrol over the Mobil because I like Larry Perkins better than Peter Brock :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...