Jump to content
SAU Community

Recommended Posts

"new topic" creates a new thread. This wanted to buy thread means you no longer have to clutter up the main page with i need this, wtb that, its all conveniently stored in one location :)

Looking for a cheap thrash car like a manual datto, ke70, gem ect to do some rallying and other motor events. Budget is about a grand unless you have something really of interested and would be interested in swapping for a 32 GTST.

Send me a PM if you've got anything. :D

I got a datsun 120Y Wagon 4 on the floor if you really want to swap your 32 for it :)

hey, im looking for some r33 GTR rims

WITHOUT tyers would be better unless theres semi slicks on them already

willing to swap some 34 gtt rims with tyers and cash if your wanting too

still looking for these rims people

also im looking for the brace thing for a cd player that holds and bolts it into place for a r33 s1 center

and if youve got a cd player to go with it i might take that too (as long as its got ipod plug)

need a engine crane to borrow over night, will give a carton of beer or summin. pref somebody down south near showgrounds. pm me cheers

After drivers side reverse light (the one flanking the numberplate) for an R32

PM me if you got

-D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...