Jump to content
SAU Community

Recommended Posts

Hey all, I just managed to get my car running really nicely, now after driving for about half an hour over the mountain I turned around at the bottom to go home and then on boost there was a slightly demented whistling noise that increases with more boost, like there is air excaping under the pressure. I have checked all the hoses and they are tight. I went for another drive and the whistle seemed to flutter when I went over a bumpy section of road, could this be the standard bov giving up? or could it be something else? -I had a turbo die rercently, and it sounds different, oh and I am running standard boost, any ideas much appreciated :)

Link to comment
https://www.sau.com.au/forums/topic/144229-whistling-noise-on-boost/
Share on other sites

Double check ALL hose clamps.

I had a similar experience. The clamps SEEMED to be firm, but after replacing the joiner hoses some months ago there was evidently some compression of the rubber that decreased the effective clamping pressure. Another half-turn on the clamps cured it.

Not coincidentally, I noticed the noise increasing when I bumped up boost from 10 - 14psi and began developing the fuel map to suit.

Thanks Dale, I will take them all apart tonight, clean them up and re-assemble :P

Edit: Fixed, it was the turbo - the bolts attatching it to the manifold were a little loose, thanks guys

Edited by Medium Dave
Check your turbo gaskets. My 33 GTR had a whistle on boost and it turned out to be a dodgy gasket.

definitely what he said, mine whistles (sounds more like a loud screech) onto sudden full boost like when your clutching it to take of hard, its the gasket that mounts the turbo onto the exhaust manifold, gas is trying to escape through a tiny passage somewhere in the gasket.

Yep, same problem with my R33.

Took off the turbo last Friday for an upgrade and i realised the rectangular gasket from the collector to the turbo had may deep cracks in it.

Must of had one more thrashing in it left before it leaked constantly. :laugh:

Hi, my series 2 33 GTST has been developing the same problem. It makes a harsh screech as it comes on to boost (It does have a massive Blitz pod filter). I always thought that is was due to the nylon compressor wheel. If I was to do the gasket off the manifold to the turbo, would there be any other gaskets that would or should require replacement?

Cheers,

Chris.

Edited by Chris_R33GTSt
Hi, my series 2 33 GTST has been developing the same problem. It makes a harsh screech as it comes on to boost (It does have a massive Blitz pod filter). I always thought that is was due to the nylon compressor wheel. If I was to do the gasket off the manifold to the turbo, would there be any other gaskets that would or should require replacement?

Cheers,

Chris.

yeah thats pretty much the only one, not sure from memory if theres one at the down pipe from the back of the turbo just double check and theres one metal gasket on the outlet of the turbo(compressor side) but you can reuse that one for sure as i have many times

yeah im pretty sure its the turbo/dump gasket. had a dodgy front pipe installed before with a leak that created the whistle sound. installed a proper dump pipe and the noise went away. scraped my cat on a speed bump which must have losened the joints and the whistle is back. gonna have to re-tighten the dump again when im free.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...