Jump to content
SAU Community

Recommended Posts

I was hoping you would say that Peter.

I have almost finished putting the event togther. I am going to make it team based with two catagories:

1. Street - street tyred car.

2. Race - Semi slick tyres.

There will be several events to earn points from.

I will put up full details shortly.

Paul

sounds good. I'll probably run on street tyres again.

Come out to the Feb 02 track day and qualify. I will be opening it up for booking shortly.

Anyone who is not on the mailing list yet please PM me your email address or join at www.TimeAttack.com.au

I think the shoot-out is going to be a great event. I will post full details soon.

Paul

going by last track day, i could be in the street tyre teamlooking at the times with 7 month old fuel. this time i might bleed the rears and start setting up the car properly. ie maybe check the tyre pressures at least with-in 8 months of track day, put in some newer fuel, at least a day or so before hand and maybe something exotic like shell 100 this time!!!! Then i can go out on my 6 year old second handies again and see what times i get in the cooler temp of the morning.

I think also some driver experience on the national track will help a lot, not just run in and get use to new pads, rotors, seating position, pedals, wiring,,, everything on the national.!!!!

I dam sure learn't a lot that day and are making changes at this moment.

Awsomely fantastic day, and will be ready for the 4WD combat challenge.

count me in for sure.

GO GODZILLA !!!!

Edited by jetman

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...