Jump to content
SAU Community

Recommended Posts

do you have the drivers side A-Pillar for GTR (if I get a defect for tacho, might sell it and get something smaller..)

also, do you have that thing on drivers side where you close the door in the car, basically where the power window control is but jus under it.. not sure what it's called :P for GTR

Edited by dalostcambo
  • Replies 140
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

do you have the drivers side A-Pillar for GTR (if I get a defect for tacho, might sell it and get something smaller..)

also, do you have that thing on drivers side where you close the door in the car, basically where the power window control is but jus under it.. not sure what it's called :P for GTR

No sorry havent got any a pillar panels, but i do have the other bit...but where the screw goes in at the bottom is broken, but still would look fine, you would have to maybe glue it in or something, where you put your hand to close the door ey?

No sorry havent got any a pillar panels, but i do have the other bit...but where the screw goes in at the bottom is broken, but still would look fine, you would have to maybe glue it in or something, where you put your hand to close the door ey?

just under that, mine has a crack..

Bump - couple of bits added.

32 GTR Fuel Pump

33 GTR 02 Sensors

GTSt Clutch Master Cylinder

GTSt Boot Lid - SOLD

GSTt Spoiler

Pics available upon request.

  • 2 weeks later...
  • 2 weeks later...

HEY Russ hows it going?

I will post one up in about 5mins for yas.

*edit* Pic is up, boot has no dents or deep scratches, it could do with a good polish tho, bit dirty, has been sitting for a while.

HEY Russ hows it going?

I will post one up in about 5mins for yas.

*edit* Pic is up, boot has no dents or deep scratches, it could do with a good polish tho, bit dirty, has been sitting for a while.

Thanks man.

All is going well but it sucks without a licence.

I'll take the boot lid coz I've just bought a GT wing and want to still keep the stock one. And it's the right colour.

Would you be able to drop it off to my place? I'm only 5-10 mins away. Not driving sucks...

Do you have any pics of the gtr side skirts?

* EDIT * Pics of side skirts added, ive only got the rear long sections, havent got the front parts. Taking offers on these.

Offers on parts with ' - offers' will be taken!

  • 3 weeks later...

Apexi GTR Pod filter setup as new

32 GTR Turbo perfect shaft play

32 GTR Bilstein Shocks only - may fit gtst as well..?

32 GTR Aircon Compressor

32 GTR Aircon Receiver Dryer BRAND NEW

More shite added!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...