Jump to content
SAU Community

Recommended Posts

do you have the drivers side A-Pillar for GTR (if I get a defect for tacho, might sell it and get something smaller..)

also, do you have that thing on drivers side where you close the door in the car, basically where the power window control is but jus under it.. not sure what it's called :P for GTR

Edited by dalostcambo
  • Replies 140
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

do you have the drivers side A-Pillar for GTR (if I get a defect for tacho, might sell it and get something smaller..)

also, do you have that thing on drivers side where you close the door in the car, basically where the power window control is but jus under it.. not sure what it's called :P for GTR

No sorry havent got any a pillar panels, but i do have the other bit...but where the screw goes in at the bottom is broken, but still would look fine, you would have to maybe glue it in or something, where you put your hand to close the door ey?

No sorry havent got any a pillar panels, but i do have the other bit...but where the screw goes in at the bottom is broken, but still would look fine, you would have to maybe glue it in or something, where you put your hand to close the door ey?

just under that, mine has a crack..

Bump - couple of bits added.

32 GTR Fuel Pump

33 GTR 02 Sensors

GTSt Clutch Master Cylinder

GTSt Boot Lid - SOLD

GSTt Spoiler

Pics available upon request.

  • 2 weeks later...
  • 2 weeks later...

HEY Russ hows it going?

I will post one up in about 5mins for yas.

*edit* Pic is up, boot has no dents or deep scratches, it could do with a good polish tho, bit dirty, has been sitting for a while.

HEY Russ hows it going?

I will post one up in about 5mins for yas.

*edit* Pic is up, boot has no dents or deep scratches, it could do with a good polish tho, bit dirty, has been sitting for a while.

Thanks man.

All is going well but it sucks without a licence.

I'll take the boot lid coz I've just bought a GT wing and want to still keep the stock one. And it's the right colour.

Would you be able to drop it off to my place? I'm only 5-10 mins away. Not driving sucks...

Do you have any pics of the gtr side skirts?

* EDIT * Pics of side skirts added, ive only got the rear long sections, havent got the front parts. Taking offers on these.

Offers on parts with ' - offers' will be taken!

  • 3 weeks later...

Apexi GTR Pod filter setup as new

32 GTR Turbo perfect shaft play

32 GTR Bilstein Shocks only - may fit gtst as well..?

32 GTR Aircon Compressor

32 GTR Aircon Receiver Dryer BRAND NEW

More shite added!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...