Jump to content
SAU Community

Recommended Posts

Hey guys. I went to Morapowa today and got my car dynoed. I managed 161.6 kws atw which im very happy about. Mods are a full exhaust and very dirty airfilter. My AFRS are really good and i was running only 8psi when i made max power.

All in all im very happy, and the dyno i ran the car on was recalibrated last week by DD, so its pretty close to 100% accuracy.

Thanks goes out to The guys at Morapowa, namely Martin Donnan.

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/
Share on other sites

Hi EnricoPalazzo, did Martin give you any clues as to the reason for the dip in the power at 160 to 165 kph? Having seen a number of similar charts thus is a common issue. As usual, it doesn't show up as an air fuel ratio problem. It has intrigued me for quite a while now and I was wondering whether Martin had encountered it as well.

Thanks for the post.

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-295811
Share on other sites

Nah he never told me about that dip, althou it seems common on all skylines. Im pretty happy with the result, as it is only a benchmark for me, and it will in the end give me a good comparison of what power i have made with the future mods that i am gonna do. Lets hope i can crack 200 rwks even thou some people think its not possible.

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-297700
Share on other sites

Originally posted by hippy

let me know what u do :)

At the moment I've dyno'd my car at 203rwkw with basic mods:

1995 S1

70,500km

Stock ECU

Stock Turbo

FMIC

HKS Pod Filter

2 Stage boost controller

Full 3" Exhaust with 3" Cat

7psi = 186rwkw

12psi = 203rwkw (leaning out at the top)

I was quite suprised by these results because similar model cars with similar mods (some even with PoweFC's) were still doing around the 170-190 power mark on that day.

http://skylines.pnc.com.au/dyno-203rwkw.jpg

From here I plan on installing a Malpassi Fuel Regulator (have it already just a matter of fitting/tuning it) and then an Exhaust Cam Gear.

Im hoping this will get me up to around 210rwkw figure.

From their its onto a PowerFC and thats about it for power mods, the rest will be seats, bodykit, wheels and im done (so I hope).

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-297721
Share on other sites

After reading Rev210's posts, i think i will get a lightened flywheel before an I/C. I think ill hit 170-180 with boost set to 11-12psi and with thermal wrapped intake pipe and front pipe. CAI and partition, cleaned airfilter, service, "Hi-flow" cat, removed rear mesh from maf, and more timing during dynoing.

My AFRs are really good for a stock ecu. At 11.5 at max power 162kws and only 8 psi, i feel im gonna make a bit of power.

And to repeat, the Morpowa Dyno was only calibrated a week ago, so the result is very accurate.

Does anyone know much about water injection or water spray kits?

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-297763
Share on other sites

Matt - hate to tell you mate, but even with my car's power it still feels slow... :uh-huh:

It only ever feels fast for a week or two... Then you feel like you've lost power... But if you run it on a dyno - same power! :burnout:

BTW - Why's everyone running in shootout mode these days?

matt

Originally posted by whatsisname

I know what you mean about it feeling slow, mine feels slow too. You get use to the power & it starts to feel slow :D

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-299574
Share on other sites

We spend all this money & the fun only really lasts a wk or 2 ;)

Originally posted by matlowth

Matt - hate to tell you mate, but even with my car's power it still feels slow... :uh-huh:

It only ever feels fast for a week or two... Then you feel like you've lost power... But if you run it on a dyno - same power! :burnout:

matt

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-301222
Share on other sites

Is it true that you actaully get a better power output ( Figure ) in shootout mode?

I managed to get 125rwkw in my r32 with the same sorta basic mods and 20 deg advanced timing on 10psi. I was under the impression that the r33's and 32's have a 20 odd kw difference in stock form?

btw. Nice work enrico ;)

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-301683
Share on other sites

I have been told that Shootout mode gives higher readings thats why i asked him not to do it in that mode, but the guy told me that Shootout mode is accurate and takes into account different variables (air temp, humidity etc etc) which the normal mode does not.

So from what i gather, No it doesnt giver higher readings, but im sure it will be argued that it does.

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-301782
Share on other sites

From all the dyno readings I've seen, it gives an extra 10%.

One car made 226rwkw at a dyno in shootout mode, and then the same day, made 206rwkw at Frankston tafe in the normal mode...

A Supercharged V8 Clubby which made 312rwkw in shootout mode in adelaide made 280rwkw on this dyno.

Normal mode does take air temps into consideration, and compensates, that's why you don't stick the temp sensor inside the engine bay...

Link to comment
https://www.sau.com.au/forums/topic/14597-r33-dyno-results/#findComment-302110
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...