Jump to content
SAU Community

Recommended Posts

Hey,

There are ppl putting r33\r34 fronts on stageas, so would you be able to do the reverse? (Stagea front on a r33)

stagea-autech.jpg

r33-1.jpg

What is involved with the front conversions to put skyline front on stagea? would it be pretty much the same process to do the stagea front on a skyline?

I just want to try and make a "unique" r33 which is damn hard to do.

Edited by R.B. Boy
Link to comment
https://www.sau.com.au/forums/topic/147279-stagea-front-on-r33/
Share on other sites

The Stagea shares a similar chassis number as the ER34, being WCGN34, so dimensionly they are similar, but not the same

The Stagea front end conversion to R34 GTR uses custom guards to go from the Stagea door shape to the R34 front and a R34 radiator panel which needs some work to fit, along custom brackets to mount bonnet

If you were going to try a Stagea front to a Skyline the best car would be a R34 not a R33

I am half way thru a Stagea front end conversion

http://www.skylinesaustralia.com/forums/in...howtopic=137313

i rekon the stagea front is too square for the r33's roundness if u get what i mean. keep in mind tho i know sfa about stageas having never seen one in the metal b4.

either way i rekon that you would have achieved the impossible and create a unique 33 if u pull this off. keep us posted and good luck

In an attempt to make a r33 "unique"

Lots of other ways to make a 33 unique, but each to their own I guess. You might wanna get someone to photochop a stagea front on to a 33 before you even start. You don't want to blow all tht $$, time and effort and have an outcome that you're not happy with and make it even harder for you to sell when the time comes...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...