Jump to content
SAU Community

Recommended Posts

Hey guys,

Can someone confirm that you can fit 18x10 +22's on a r32 GTR. I am thinking of buying a set. I know they will stick out a bit on the outside (thats what i like) but im more worried about the inside hitting the struts?

Also what size tyres would work, may need to stretch em? 235/35 or maybe 245/35's?

Link to comment
https://www.sau.com.au/forums/topic/148083-18x10-22-wheels/
Share on other sites

I doubt they will fit on the front. I've had 18x8 +38 on the front and they JUST fit. 18x10 +22 will stick in another 9mm. If you get a skinny enough tyre you could probably fit them.

On the rear, you will be fine

Link to comment
https://www.sau.com.au/forums/topic/148083-18x10-22-wheels/#findComment-2764392
Share on other sites

9 +22 will fit. I've got 9 +20 on the front of mine with a good amount of clearance.

You could get staggered sizes?

i think i might go with 18x9 + 8 instead which works out to give the same dish but more clearance on the inside and stick out just as much on the outside! :) I used to have a set of 18x9.5 +14 and it fit nicely too.

Link to comment
https://www.sau.com.au/forums/topic/148083-18x10-22-wheels/#findComment-2764600
Share on other sites

They will fit but you have to remove inter guards and roll the guards Front to rear.

EDIT:I see you already have 18x9.5 +14 with no mods so at the same ride hight 18x10+22 must come close to fitting? When i wanted rims the above is what i was told.

Link to comment
https://www.sau.com.au/forums/topic/148083-18x10-22-wheels/#findComment-2765694
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...