Jump to content
SAU Community

Pimp -n- Ho's Cruise

_MRR33

By _MRR33,
in Events

 Share

Recommended Posts

_MRR33 Experienced

_MRR33

Posted
Posted (edited)

Doesn't look like theres anything planned tonight so I thought I might as well organize a cruise to Broadwater Car Park.

Please post here if you are going to come, and any Northsiders are more then welcome to organize a meeting spot at Aspley Hypermarket and meet is at Springwood at 7:30pm.

Once we do get to Broadwater Car Park, if people want to do something from there we can organize something. Hope to see a few of us out tonight!

First Meeting Spot:

Springwood Crazy Clark's

Arrive: 7:30PM

Depart: 8:00PM Sharp

Second Meeting Spot:

BP Yatala

Arrive: 8:20PM

Depart: 8:45PM Sharp

Third Meeting Spot:

Broadwater Car Park

Arrive: 9:10PM

Things to Bring:

1. Full tank of fuel

2. Camera

P.S: You don't have to be a pimp or a ho to attend :teehee:

So, I'll see you all there! Everyone is welcome!

Edited by GTS793
Link to comment
https://www.sau.com.au/forums/topic/148477-pimp-n-hos-cruise/
Share on other sites
_MRR33 Experienced

_MRR33

Posted
  • Author
Posted
damn if i had of seen this earlier i would have been there but started drinkin already lol

:teehee: You've started early, how many have you had? We're not leaving until 8PM, meeting at 7:30.

Have some water and a sleep :D Better not, just in case you are over the limit still.

Revhead Grand Master

Revhead

Posted
Posted

I've been there on more than one occasion when the cops have decided to lock down the ENTIRE carpark and inspect every single car on the way out. The police regularly patrol it (good) and sometimes go absolutely stupid with defects. One guy showed me a defect on a bone stock rental car for a half-full washer bottle. I've heard of empty washer bottles being defected (pedantic but understandable) but half full?? If that's not a hot spot I don't know what is.

That said it has calmed down a lot recently, but it's still worth being informed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...