Jump to content
SAU Community

SA Wasteland?

MM2death

By MM2death,
in South Australia

 Share

Recommended Posts

vange Experienced

vange

Posted
Posted
i just changed my avatar pic vange, what is it your having trouble with? it took me a while to get it working

i choose the pic from my comp, i did a totaly diff pic..i chose a pic of a monkey, and the 1 i got now comes up...all blured...

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Tangles Grand Master

Tangles

Posted
Posted

hhmm, Vange..... you got a damn good 'bod (if that is indeed you all sun-tanned in the avatar pic) is all I'll say :teehee::O

On a side note, your previous avatar picture, going back a few months, with the front end of your white R33, looked TOO MUCH like a Lancer. Why is it that on some angles, white R33's from the front look like Lancers?

vange Experienced

vange

Posted
Posted

i was just thinking b4....we had the problem that we didnt know when we c another skyline if they r on sau or not...well i have that problem lol

instead of stickers, how about a special 'signal' so we know..

in most cases, we c the other car travelling in the opposite direction, so how about when we c other lines, we flash our breaks a few times, and if they do the same, u know they r sau :)

also if they r behind u, flash ur breaks, n respond with a quick flash of the highbeams. same would work when crossing paths at an intersection.

any1 else think this is a good idea, or should i just shut up?

Bl4cK32 Grand Master

Bl4cK32

Posted
Posted

we discussed this a while ago....doing the nod, 1 finger off the steering wheel etc...too damn hard.

Everytime i see some other knob in a jdm car out on the road and im in my line, they are always looking at me sly to see what im driving for some reason, or they have a mate with them that is breaking his neck to have a look...what the f**k is so special about other peoples cars?? Especially my beat up wreck??

I undertand people seeing others they know, but racing, and trying to "impress" me with doing skiddies on the road aint funny at all....it just draws attention to me, which isnt cool if i get defected!

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...