Jump to content
SAU Community

Recommended Posts

Hi Guys,

Removing my standard rear speakers on a sII R33 in getting the car ready for window tinting.

Anyone whos done this before care to give some advice or steps as not as not straight forward as i thought..

i have undone the main center bolt... but not sure what to do next, do i rip up the grill (very hard to get off)?? If i do i think im going to damage it....

Is there some concealed screw / bolt that needs to be removed from the bottom that i dont know about?

why cant there be a DIY guide on this :-)

cheers

Edited by ASTRO_R33
Link to comment
https://www.sau.com.au/forums/topic/148656-r33-standard-rear-speaker-removal/
Share on other sites

Take rear seats out. Bottom part first - 2 bolts at front just under lip of seat.

back is another 2 bolts by seatbelt anchors. The push seat up and pull out.

Rear tray has the C pillar trim clipped into either side. just caefully bend tray to get out. Pull towards front of car without lifting as there are a few clips that clip to metal parcel tray. Speakers are bolted to mounts that are bolted/screwed to metal parcel shelf.

_________________

My 33 doesnt have rear speakers, only holes where they once were!

Are you trying to remove just the speakers, or the whole parcel shelf?

Can't the window tinting guys work around the rear speakers anyway???

hahaha. my 33 doesn;t have rear speakers either. just small holes in the parcel shelf. and wires. haha.

the dude in japan must of taken them out. :(

Sounds like he's removed the parcel shelf guys!

thanks for the replies...

yep speakers covers came out, was hoping to do it without removing parcel shelf but had to remove it.

I'm pretty sure complete parcel shelf setup was stock SII (Sanyo 30W speakers and covers that had a bolt through the middle of them?).

All good :-)

  • 2 months later...
  • 2 weeks later...
thanks for the replies...

yep speakers covers came out, was hoping to do it without removing parcel shelf but had to remove it.

I'm pretty sure complete parcel shelf setup was stock SII (Sanyo 30W speakers and covers that had a bolt through the middle of them?).

All good :-)

heh.. the bolts through the middle of them are for compliance usually. They have to put the child restraint bolts in, and through the speaker is where they need to be!

install some mad speakers in the rear (focals)

then put the stock parcel tray back in and glue the restraint plastic covers over the stock grills

cut the top of the bolt end off and glue it so it looks like its actually in place. :-) looks like its compliant but the po po wont no

lol FTW

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...