Jump to content
SAU Community

Recommended Posts

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

im deffinetly interested just want a def answer if mods have to be done to the gaurds to make them fit on an r34.

i also want to know this.

if this is a direct fit kit, as in u fit the hindges and clamp the doors on and away they go....then fine im in.

but if custom work has to be done to the doors and all this other stuff...its another story

More info guys ...... :(:(:)

Not bolt only kit. Haven't started as yet, but have instructions now. Still shouldn't be too bad, but will let you know of the progress. It looks like we will be doing it next week some time.

For those interested, I have attached the instructions. Looks like there may be some welding and the fenders may need to be rolled by the looks of it. I will let you know how much once we do it.

VDK.pdf

Just to let u guys know, I have a very similar hinge in my car. It took alot of mods and trial and error. I also work for a modification shop and can tell u that to fit a kit like this will be in excess of $1500 for labour. And if you get someone who dont know much about them to fit it, they can severly stuff it up, in some cases irreversable. So do ur research first to make sure u get quotes on fitting before ur embarking on doing something like this.

I chose this type of kit also cause it allows to door to lift in excess of 90degs, which the bolt on kits cant even get close to (usually 50-60deg).

Looks good.. although would definitely need a pro to install it.. Is there anyone/shop in Melbourne who install these things?

I think IQ auto used to do it.

Edited by Janissary

Thanks for the heads up Mr Cali.

Can you tell me what things I should look for and what problems can happen before I start.

Thanks. I will still keep everyone updated on the progress of this.

Cheers,

Sam

Here are some pics, hope it works...

post-33008-1167379186.gif

click on the image as it is an animated gif....

where did you get the pic's for that animated gif?? ....nice to know someone is using a picture of my car for advertising....

i installd a similar kit myself, they are illigal unless you get MOD plateing in QLD, i can help anyone instal them if they are in the area of brisbane.

CJ

PS, i got a 20min video showing exactly what has to be done to put these doors on. and yes wider fenders would be a benifit.

before you install note that the wingdoors will feel slightly wobbly,

also with these kits they are only for show, unless you are insanely muscly you won't be able to get out of the car by lifting the door. he door will be able to open normally to about 30 degrees for you to get in and out, if you want to lift them, you need to be actually outside of the car

also since the whole door is only supported by one hinge allowing vertical movements, as you shut the door, the hook where the door is suppose to lock into will not align with the latch...hard to explain, but you'll know it after you install them~~

mine close properly, with the door sensor also still working, mine works on a gas stut, so even my gf who only weighs 55kg can lift it up without straining herself haha.

  • 4 weeks later...

Guy's sorry it's taken so long to get back to you. The details so far .......

No way is it bolt on and mod's needed are a fair bit. Getting help from a panel beater and he recommends that a plate is welded on to support the hinge as the body behind the fender area where the hinge is to attach is too thin and not flat.

The hinges will be started on Monday and may take 2 or 3 days. I will take photo's of the entire process in the event that anyone is still interested. Sorry if I lead you astray. What they say, and what you get a 2 different things :wave::( This job appears to be one not for the faint hearted and someone that's pretty handy.

I'm still not sure if the guards need rolling anymore with unpicking a section of the body and putting in a 3mm plate. Will know in a few days :D

Will keep you posted of the progress.

Edited by Filecon

Awesome Sam. No worries about leading us astray. You weren't leading us astray at all. You tried to get us a good product at a good price.

It just turns out that it's not for the faint hearted, that's all :(

  • 3 weeks later...
  • 3 weeks later...

I had one of these type of kits, although mine was actually a full bolt on from Japan, cost me $1200NZD

so a bit expensive :S but yeah

my kit needed a bit of modification to the inside guard(hammer took care of it) - panelbeater should be able to do it in about 30 minutes

and the inside fender needed to be cut a bit, i used a grinder to remove the inside of it and it worked fine

the wires in the r32's are long enough to reach out, it'll take about 2-3 hours to adjust it to the right fit, but once they fit on, they do look good :pirate:

I'd definitely recommend the heavy duty gas struts, if you try lifting one with a normal strut, it's extremely hard, with the gas strut, you lift it about a cm and the door pushes itself mostly up :ph34r:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers)
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
×
×
  • Create New...