Jump to content
SAU Community

Recommended Posts

remember you can get the apexi pods for $90 delivered now..

can someone post a link to this article? i haven't seen it before. or at least post the gist of it, are they saying the cheap ass 3a ones are better than apexi?

Link to comment
https://www.sau.com.au/forums/topic/149467-3a-air-filters/#findComment-2789225
Share on other sites

remember you can get the apexi pods for $90 delivered now..

can someone post a link to this article? i haven't seen it before. or at least post the gist of it, are they saying the cheap ass 3a ones are better than apexi?

That is correct, i read it in the latest AutoSalon magazine, dont know of an internet link. Will look for one though.

Link to comment
https://www.sau.com.au/forums/topic/149467-3a-air-filters/#findComment-2789322
Share on other sites

Ok, here is a few of the details (sorry no scanner)

*as i sit here NOT working*

there were 2 main scores Flow and Filtration... there's what they listed

* AEM Dryflow -- Flow 9th @ 519.2cfm, Filtration 3rd, Price $100

* A'PEXI Power Intake -- Flow 7th @ 533.3cfm, Filtration 6th, Price $125

* HKS Direct Drive -- Flow 6th @ 539.6cfm, Filtration 9th, Price $125

* K&N RR-3301 -- Flow 4th @ 579.6cfm, Filtration 1st, Price $125

* Redline Airforce 1 -- Flow 2nd @ 596.9cfm, Filtration 10th, Price $40

* Simota Power Stack WS-002 -- Flow 3rd @ 594.2cfm, Filtration 5th, Price $29.95

* Tenzo WS002-CH -- Flow 8th @ 522.8cfm, Filtration 4th, Price $19.95

* 3A Racing -- Flow 1st @ 601.2cfm, Filtration 2nd, Price $28.95

* Trust Airinx -- Flow 5th @ 554.7cfm, Filtration 7th, Price $120

* No Name (Trust Imitation) -- Flow 10th @ 473.3cfm, Filtration 8th, Price $15

there's more info and more pics etc in the mag...

Link to comment
https://www.sau.com.au/forums/topic/149467-3a-air-filters/#findComment-2789932
Share on other sites

3a_power_stack_filter.jpg

well they might flow better and filter good, but for how long, what is the longevity of the filter life. u mite only get a 3rd of the life from one and u will have to change it 3 times as often. a mate had one of these on his 200sx, but not sure how it went.

im sure this is the filter though.

Edited by 85URK
Link to comment
https://www.sau.com.au/forums/topic/149467-3a-air-filters/#findComment-2790795
Share on other sites

  • 4 weeks later...
I've actually been running one of these for a few months...personally didn't notice any difference over the previous K & N

I must admit I never even noticed it had 3A Racing on it :P

ha ha fair enough.

in the end of the day i dont think the difference is going to be that big it will give u major hp gains.

i am look for a replacement filter for my k&n atm, but not sure what to get, as i already have the adapter for the k&n i was thinking of getting another one to fit the adapter as it is a really wide mouth adapter, but i got told they are expensive to buy.

Edited by 85URK
Link to comment
https://www.sau.com.au/forums/topic/149467-3a-air-filters/#findComment-2857666
Share on other sites

3a_power_stack_filter.jpg

well they might flow better and filter good, but for how long, what is the longevity of the filter life. u mite only get a 3rd of the life from one and u will have to change it 3 times as often. a mate had one of these on his 200sx, but not sure how it went.

im sure this is the filter though.

I've had 2 on my RB26 for over 2 years now, they filter very well (have had an oil analysis done which supports this) and are well made - very similar to previous K&N filters that I have owned. Better filtration and flow than Apexi and 1/3rd the price - how can you go wrong!? :happy:

Link to comment
https://www.sau.com.au/forums/topic/149467-3a-air-filters/#findComment-2858452
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...