Jump to content
SAU Community

Recommended Posts

This is a regretful sale, of my near new Microtech ECU, plug and play adapter and laptop dongle, its only been in my car a month, but xmas is left me a bit behind so i need the money to pay some bills.

ECU is still in my car located in Brisbane, i can show you it working and running the car if needed, or i can post to anywhere at the buyers expence

All of the above was purchased for $1695 just on a month ago direct from Microtech, The ECU has a lite tune on it for the basic mods, Bigger turbo, 15psi, fuel pump, full exhaust and cam gears.

I am looking for $1400 for the three items, like i said there close to brand new so this is a good deal for anyone needed and aftermarket ecu

You can contact me on email at [email protected] or msn on [email protected]

Ask any questions you have i will happily answer them, once again this is a regretful sale and needs to go quickly.

Cameron

Edited by murrayis

it was making 270 rw hp on 15psi but very very lean but that was because of the stock injectors, on 11 - 12psi we left it at 225hp there abouts.

It made alot of diff up top, and really smoothed out the transition onto boost, it is making 225hp at 5200 just after it comes on full boost

so it has the rb20 adapter, std map sensor? and does it have the microtec ignitor or not? the *laptop dongle* is the cable for lap top tune? if so do you have software? still undr warrenty i assume.

if this is an rb20 ecu...if i wanted to put it in an rb25, i'd have to re-tune it?

is wired in or just plug in?

Put it this was the base map that microtech sends with the ecu for the rb20det is for the rb25det, all the difference is in the plug and play adapter and yes of course would have to fiddle with the tune as you would with any ecu swpapping between engine types, you might find it wouldrun without any problem then again you just don't know

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...