Jump to content
SAU Community

Recommended Posts

Dan's on holiday at the moment and working from home.

Best way to contact him is his e-mail address, so e-mail him and he'll give you a contact number. Awesome guy and he's doing my major service this weekend.

He's been building a RB30/25 for somebody as of late and it sounds like he gives it 100% too.

He'll of course try his best to find out what caused it too so you know what else may be at fault.

Good luck and sad to hear about the engine!

i used john hill of JHH Engineering, prolly the best performance engine builder in aust thumbsup.gif

thats the funniest thing i have read in a long time, id be more worried about finding more sand in my engine than in the sahara desert.

thats the funniest thing i have read in a long time, id be more worried about finding more sand in my engine than in the sahara desert.

Hey Ben,

I know of another mechanic who used to send his work to JHH and suffered the same sandy fate.

thats the funniest thing i have read in a long time, id be more worried about finding more sand in my engine than in the sahara desert.

from what i heard all u got done to the head was sandblasted and john gave it back to you, so if u didnt check it, its ur own fault :worship:

the head was sandblasted and ported by somewhere else and given the workshop in question for a full head service, that includes cleaning out the head.

But you really are the expert on heads arent you shane????

from what i heard all u got done to the head was sandblasted and john gave it back to you, so if u didnt check it, its ur own fault :huh:

You should really try not to make comments like this when you have no idea. Who gave you that information?

The head was sandblasted and ported and John was fully aware that the head had been on the sandblaster. The head was completely stripped when I gave it to him and I payed in the vacinity of $600 for a complete head service including valve regrind etc.

The block and head are at another engineers now after engine failure and it has been found that the gallery plugs have not been removed from the block or head. The gallery plugs were not removed from the crank AS REQUESTED for cleaning, and the cylinders were bored with insufficient clearance for the pistons even though the spec sheet was supplied with the pistons.

As a result he destroyed a set of ROSS piston rings

He nearly destroyed a full set of brand new ROSS pistons

He destroyed every main and conrod bearing.

He nearly destroyed a brand new N1 oil pump

As I am a man of my word I am covering the engine under warranty. This is costing me around $1000....maybe a little more.

So please do not make comments like these when you don't know what really happened.

Oh, and I'm not bagging out JHH engineering either....who knows, maybe he just forgot to check that stuff in his old age. Fact is I payed him for a job and he only did half. I know I will never use them again and I will never recommend them to anyone ever again. I think I payed for that right.

You should really try not to make comments like this when you have no idea. Who gave you that information?

The head was sandblasted and ported and John was fully aware that the head had been on the sandblaster. The head was completely stripped when I gave it to him and I payed in the vacinity of $600 for a complete head service including valve regrind etc.

The block and head are at another engineers now after engine failure and it has been found that the gallery plugs have not been removed from the block or head. The gallery plugs were not removed from the crank AS REQUESTED for cleaning, and the cylinders were bored with insufficient clearance for the pistons even though the spec sheet was supplied with the pistons.

As a result he destroyed a set of ROSS piston rings

He nearly destroyed a full set of brand new ROSS pistons

He destroyed every main and conrod bearing.

He nearly destroyed a brand new N1 oil pump

As I am a man of my word I am covering the engine under warranty. This is costing me around $1000....maybe a little more.

So please do not make comments like these when you don't know what really happened.

Oh, and I'm not bagging out JHH engineering either....who knows, maybe he just forgot to check that stuff in his old age. Fact is I payed him for a job and he only did half. I know I will never use them again and I will never recommend them to anyone ever again. I think I payed for that right.

WELL I WOULD PUT IN A VOTE FOR JOHN AND WILL AT JHH.

BUILT MY RB25/30 DET AND IT GOES LIKE A SHOWER OF SHIT FOR A 35/40, STANDARD VL FUEL SYSTEM AND 25 INJECTORS. IM VERY HAPPY AND IN THE EVENT I GET ANOTHER PROJECT CAR(f**kED IF I WOULD PUT MYSELF THROUGH IT AGAIN) I WOULD DEFINATELY GO TO HIM AGAIN.

HORSES FOR COURSES BUT I WAS HAPPY.............

MY 2C

CHEERS

IMTORQING

WELL I WOULD PUT IN A VOTE FOR JOHN AND WILL AT JHH.

BUILT MY RB25/30 DET AND IT GOES LIKE A SHOWER OF SHIT FOR A 35/40, STANDARD VL FUEL SYSTEM AND 25 INJECTORS. IM VERY HAPPY AND IN THE EVENT I GET ANOTHER PROJECT CAR(f**kED IF I WOULD PUT MYSELF THROUGH IT AGAIN) I WOULD DEFINATELY GO TO HIM AGAIN.

HORSES FOR COURSES BUT I WAS HAPPY.............

MY 2C

CHEERS

IMTORQING

That's nice....but why are you shouting?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes. Probably, given that there is only access from the bottom end of it, go with a drill bit. Don't start too small. 7 or 8mm is probably the right size. You want something that can make a big enough hole to do some damage, but not so bit that it clashes with the steel or binds up and breaks your wrist. A slow speed is probably a good idea too. Once the rubber is destroyed, you then have to get the crush tube off the stud, which will be the whole heat/oil/cutting exercise all over again, but this time with the need to strictly avoid damaging the stud (any further than the corrosion might already have done.
    • We replaced the connector just because we could and it was still there, once we swapped the injectors around it stopped. The injectors were something I had thoughts of replacing even before I first started the engine and in hindsight I should have 
    • Not too sure just yet, want to have a go at doing what I can myself, but to start with want someone to cast their eye over it tell me what needs doing to get it running and back on the road, so anyone with great overall knowledge would be ideal.
    • I personally would go with cutting out the rubber. Then deal with getting sleeve off separately. Rubber can be painful to cut, it loves to jam up cutting tools. I normally have success with drill bits, deburr bits, angle grinders, jigsaw, reciprocating saw, and never forget... fire. Obviously different tools won't work in all locations you're trying to work with, and you need to be comfortable with each. You personally may be happy slowly slicing it out with a razor blade, if you are, go for it with one too! Feel free to wait for others to weigh in also on their thoughts.
    • So ... I got everything disconnected and started dropping the frame. Three of the four mounts started to come down but the fourth one (the one with the nut that gave me all the trouble) won't budge. The inner metal sleeve stays up tight against the chassis rail although the outer part of the mount drops a bit (and can be levered quite a lot more) but it's just stretching the rubber bushing. So I reckon there's some serious corrosion inside the inner sleeve and holding it tight to the lug at the top of the bolt. Tried everything I can think of so far: penetrating oil, whacking the top of the sleeve to vibrate it and wedge a screwdriver blade in there. I also tried to turn the inner sleeve a bit by hitting it with a chisel at the bottom. It's stuck solid. What do you think about cutting the rubber with a blade so I can drop the subframe around it anyway. Then worry about getting the inner sleeve off after? Will that work? Is it gonna give me even more problems?
×
×
  • Create New...