Jump to content
SAU Community

Recommended Posts

HI All

so i got my new splitfires today, put them in, ran 1.0mm gap, and getting missfire at the usual rpm 4500-6000. Only running 10psi of boost, had no problems wiht old coils at 0.55-0.6mm at the same boost,

SO WHAT THE HELL. The reason i got these is to stop the missfire and increase my gap to increas mid range pull and fuel ecconomy, so gapping down is a bit of a waste of my money.

Is it possible that the earth might be a bit crap or something?

CAN somone advise me ASAP please
Edited by WogsRus
  • Replies 92
  • Created
  • Last Reply

Top Posters In This Topic

It's a series 2 with no ignitor. In regards to bigger problems, what else can it be, could the problem be a CAS sensor or something else.

I am going to regap to 0.8 but this sux, hopefully i can sorgth it out.

I have no errors on the computer, it has been tuned, new pump and so forth, the car did not miss at 0.55 gap, but the coils were shot, i mean i could hardly see the spark.

Sorry should have explained. When i got the car stock it was ok, but soon after i saw some cracks in the coils so i silliconed them up and they ran for a bit and then got worse. SO i gapped the plugs down till they worked wich was 0.55mm.

I am running the copper plugs that everyone gets on here, the BPRS6 things, NGK, you know the ones.

My fuel ecconomy started to suffer as soon as the coild started to fail, so i am trying to fix this by trying biger and better coils with bigger gap.

Thats not the right plug code... you sure thats it?

There are a few that are similar.

If you gap them down and its working, you have a faulty connection somewhere and isnt letting the power through

Find the cyclinder thats misfiring and it will be easier

Well series two with ignitor, did check with MM, and primary is 1.4k ohms, wich is standard for series two, series ones are like .6k ohms.

AFM is clean did that, just finishing the plugs and see how it goes.

BTW i am on my lappy next to the car while working so hence the responces on the run.

OK so

gapped to 0.8mm, still get a slight miss under 3 full load, bugga. I guess there must be something else wrong, not sure what though.

Any ideas. If my engine was getting crappy earth, would that cause problems?

ALSO installed an R32 wastgate actuator, and DAm, doe the car pull much better now.

HOWEVER also noticed with the splitfires, the car idles better, more pull through the midrange (this was before the actuator), and easier starts.

SO all i need to do now i figure out why it might still be missfiring.

I read somwhere that if the CAS is playing up that might cause some issues.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...