Jump to content
SAU Community

Starting Problems

clkngezz

By clkngezz,
in General Maintenance

 Share

Recommended Posts

clkngezz Enthusiast

clkngezz

Posted
Posted

this morning i went to start my car and it normally starts fine but this morning it was kicking over and about to start but then it would go back to just turning over/kicking over! after a while i started to pump my accelerator and it took a while to start but it did! any ideas? it would be great to hear your thoughts i have priced up a new fuel pump from nissan in japan $750, so any other thoughts would be good! i have a rb25det thanks guys

Link to comment
https://www.sau.com.au/forums/topic/151372-starting-problems/
Share on other sites
clkngezz Enthusiast

clkngezz

Posted
  • Author
Posted

no mods just air filter! yeah the car runs fine after that! i was thinking if it was the fuel pump wouldnt it starve on boost if it wasnt pumping properly! i was thinking it could be plugs as well could be oiled up or somethin?

Race_Bred Enthusiast

Race_Bred

Posted
Posted
could i get that stuff from bp or super cheap FUEL INJECTOR CLEANER would that do it the job if it is the injectors?

better off cleaning properly,

injector cleaner will probably just ruin ur spark plugs like octane booster

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R34 gtt rb25det neo timing belt kit

      By Duncan · Posted

      No need to replace the cover if it is still intact (not worn through). It would be worth checking the balancer for matching marks on the rear, but I'd assume the balancer was loose at some stage. The cam timing marks look fine, once you put the new belt on you can only be right or a full tooth out
    • Duncan
      So i brought a boat...

      By Duncan · Posted

      Disconnecting rods! must have been an unpleasant surprise...
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So been ocd with timing mark but checked from few angle and seems both cam are on and crank is matching as well to the slot on sump and crank pully   i noticed crankshaft cover has been robbed as per attached pic. Any ideas why? Could my balancer or harmonic be on its way out? should I replace the cover? https://ibb.co/ZR1JFYRR
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • sunsetR33
      braided lines for the turbos

      By sunsetR33 · Posted

      Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
×
×
  • Create New...